Balluff - BVS CA-GT Technical Documentation
Device Feature And Property List
ProductFeatures
Feature Name Min Max Inc Valid Values Documentation
ProductFeatures This list has been created with Impact Acquire version '3.0.0' and firmware version '2.55.3663.0'. This does NOT imply that all these features will only be available since these versions. They might be available in previous ones as well.
Feature Name Min Max Inc Valid Values Documentation
Camera This list contains features to control the device
ImageRequestTimeout_ms 0 ms INT_MAX 1 ms - Defines the timeout for the request in ms. Once the timeout has elapsed the request object is returned to the user even if no data has been captured into it. The timespan taken into account for the measurement starts when the driver begins to capture data into this particular buffer! So when queuing 4 buffers with a timeout of 3000 ms each and no data being transmitted by the device will cause the last buffer to time out 3000*4 = 12000 ms AFTER the buffer has been queued and the acquisition has been started. A timeout of 0 never elapses.
Feature Name Min Max Inc Valid Values Documentation
GenICam This list contains all features that have been extracted from the GenICam description file of the device
Feature Name Min Max Inc Valid Values Documentation
DeviceControl A category for device information and control.
DeviceClockSelector - - - Sensor
 Selects the clock frequency to access from the device. Sensor: Clock frequency of the image sensor of the camera.
DeviceClockFrequency INT_MIN INT_MAX - - Returns the frequency of the selected Clock. (Hz)
mvDeviceClockFrequency - - - kHz_74250
 Clock frequency of the image sensor of the camera. kHz_74250: Clock frequency of the image sensor of the camera.
DeviceFirmwareVersion - - - - Version of the firmware in the device.
DeviceScanType - - - Areascan
 Scan type of the sensor of the device. Areascan: 2D sensor outputting an image created from a unique sensor acquisition.
mvDeviceSensorName - - - - This feature is deprecated (See SensorName). Shows the name of the sensor.
mvDeviceSensorColorMode - - - BayerMosaic
 Shows color mode of the sensor. BayerMosaic: Shows color mode of the sensor.
DeviceReset@i - - - - Resets the device to its power up state. After reset, the device must be rediscovered.
DeviceFeaturePersistenceStart@i - - - - Indicate to the device and GenICam XML to get ready for persisting of all streamable features.
DeviceFeaturePersistenceEnd@i - - - - Indicate to the device the end of feature persistence.
DeviceRegistersStreamingStart@i - - - - Prepare the device for registers streaming without checking for consistency.
DeviceRegistersStreamingEnd@i - - - - Announce the end of registers streaming. This will do a register set validation for consistency and activate it. This will also update the DeviceRegistersValid flag.
DeviceIndicatorMode - - - Inactive,
Active
 Controls the behavior of the indicators (such as LEDs) showing the status of the Device. Inactive: Device's indicators are inactive (Off). Active: Device's indicators are active showing their respective status.
mvDeviceStatusLEDEnable - - - 0,
1
 This feature is deprecated (See DeviceIndicatorMode). If enabled, the color of the LED changes depending on the state of the camera. Otherwise the LED is Off.
mvTimestampResetValue 0 INT64_MAX 1 - Defines the initial value after the cameras timestamp timer has been reset.
DeviceRegistersValid - - - 0,
1
 Returns if the current register set is valid and consistent.
mvDeviceRegistersStatus - - - Valid,
Invalid,
BinningHorizontalValueInvalid,
BinningVerticalValueInvalid,
DecimationHorizontalValueInvalid,
DecimationVerticalValueInvalid,
BinningDecimationCombinationInvalid,
BinningDecimationImageTooWide,
InvalidSensorShutterTriggerCombination
 Will give a hint where to find the invalid register settings if any. Valid: The current register settings are in a consistent state. Invalid: The current register settings are in an invalid and/or inconsistent state. BinningHorizontalValueInvalid: The current BinningHorizontal value is not supported. BinningVerticalValueInvalid: The current BinningVertical value is not supported. DecimationHorizontalValueInvalid: The current DecimationHorizontal value is not supported. DecimationVerticalValueInvalid: The current DecimationVertical value is not supported. BinningDecimationCombinationInvalid: The current combination of binning and decimation is not valid. BinningDecimationImageTooWide: The current Width is too wide for the BinningVertical and/or DecimationVertical settings. Please reduce the Width or add BinningHorizontal orDecimationHorizontal. InvalidSensorShutterTriggerCombination: The Image Sensor does not support the selected trigger and shutter combination. Please select another combination.
DeviceType - - - Transmitter,
Receiver,
Transceiver,
Peripheral
 This is a read only element. Its value indicates the device type. Transmitter: This enumeration value indicates that this device acts as a transmitter. Receiver: This enumeration value indicates that this device acts as a receiver. Transceiver: This enumeration value indicates that this device acts as a transceiver. Peripheral: This enumeration value indicates that this device acts as a peripheral device (with no data stream handling).
DeviceVendorName - - - - This is a read only element. It is a string that indicates the name of the device vendor.
DeviceModelName - - - - This is a read only element. It is a string that indicates the device model name.
DeviceManufacturerInfo - - - - This is a read only element. It is a string that provides additional information from the vendor about the camera.
DeviceVersion - - - - This is a read only element. It is a string that indicates the version of the camera.
DeviceSerialNumber - - - - Device's serial number. This string is a unique identifier of the device.
DeviceID - - - - This feature is deprecated (See DeviceSerialNumber). It was representing the Device unique identifier (serial number).
DeviceUserID - - - - A user programmable device ID as a string.
DeviceTLType - - - GigEVision
 This is a read only feature. This enumeration indicates the Transport Layer type of the device. GigEVision: This enumeration value indicates that this entry indicates that this is a GigE Vision device.
DeviceTLVersionMajor 0 65535 1 - This is a read only element. It indicates the major version number of the Transport Layer specification supported by this device.
DeviceTLVersionMinor 0 65535 1 - This is a read only element. It indicates the minor version number of the Transport Layer specification supported by this device.
DeviceLinkConnectionCount 0 UINT_MAX 1 - Returns the number of physical connection of the device used by a particular Link.
DeviceLinkSelector 0 0 1 - Selects which Link of the device to control. Generally, a device has only one Link that can be composed of one or many connections. But if there are many, this selector can be used to target a particular Link of the device with certain features.
DeviceLinkThroughputLimitMode - - - Off,
On
 Controls if the DeviceLinkThroughputLimit is active. When disabled, lower level TL specific features are expected to control the throughput. When enabled, DeviceLinkThroughputLimit controls the overall throughput. Off: Disables the DeviceLinkThroughputLimit feature. On: Enables the DeviceLinkThroughputLimit feature.
DeviceLinkThroughputLimit INT64_MIN INT64_MAX 1 - Limits the maximum bandwidth of the data that will be streamed out by the device on the selected Link. If necessary, delays will be uniformly inserted between transport layer packets in order to control the peak bandwidth. (Bps)
DeviceLinkSpeed INT64_MIN INT64_MAX 1 - This is a read only element. It indicates the speed of transmission negotiated on the specified Link. (Bps)
DeviceLinkHeartbeatMode - - - Off,
On
 Activate or deactivate the Link's heartbeat. Off: Disables the Link heartbeat. On: Enables the Link heartbeat.
DeviceLinkHeartbeatTimeout 0.000 UINT_MAX - - This value controls the current heartbeat timeout of the specific Link. (us)
DeviceLinkCommandTimeout 0.000 65535000.000 - - Indicates the command timeout of the specified Link. This corresponds to the maximum response time of the device for a command sent on that link. (us)
DeviceStreamChannelCount 0 UINT_MAX 1 - This is a read only element. It indicates the number of stream channels supported by the device.
DeviceStreamChannelSelector 0 0 1 - This enumeration selects the stream channels to configure. Once a stream channel has been selected, all changes to the stream channel settings will be applied to the selected stream channel.
DeviceStreamChannelType - - - Transmitter,
Receiver
 This is a read only element. Its value reports the type of the stream channel. Transmitter: This enumeration value indicates that this is a transmitter stream. Receiver: This enumeration value indicates that this is a receiver stream.
DeviceStreamChannelEndianness - - - Little,
Big
 This is a read only element. Its value indicates the endianness of multi-byte pixel data for this stream. Little: This enumeration value indicates that this data stream is little Endian. Big: This enumeration value indicates that this data stream is big Endian.
DeviceEventChannelCount 0 UINT_MAX 1 - This is a read only element. It indicates the number of event channels supported by the device.
DeviceCharacterSet - - - Reserved,
UTF8,
ASCII
 This is a read only element. Its value indicates the character set used by the strings of the device's bootstrap registers. Reserved: This enumeration value indicates that the device uses a reserved representation for all strings in the bootstrap registers. UTF8: This enumeration value indicates that the device uses the UTF-8 representation for all strings in the bootstrap registers. ASCII: This enumeration value indicates that the device uses the ASCII representation for all strings in the bootstrap registers.
DeviceRegistersEndianness - - - Little,
Big
 This is a read only element. Its value indicates the endianness of the registers of the device. Little: This enumeration value indicates that this device's registers are little Endian. Big: This enumeration value indicates that this device's registers are big Endian.
TimestampReset@i - - - - Resets the current value of the device timestamp counter. After executing this command, the timestamp counter restarts automatically.
TimestampLatch@i - - - - Latches the current timestamp counter into TimestampLatchValue.
TimestampLatchValue INT64_MIN INT64_MAX 1 - Returns the latched value of the timestamp counter. (ns)
mvDeviceFirmwareSource - - - BootSection,
ProgramSection
 Shows the location from where the firmware was loaded. BootSection: When the firmware could not be loaded from its default location (ProgramSection) this defines a fallback location. This is usually an indicator for a problem! ProgramSection: The firmware has been loaded normally
DeviceTemperatureSelector - - - Device
 Selects the location within the device, where the temperature will be measured. Device: Selects the location within the device, where the temperature will be measured.
DeviceTemperature INT_MIN(As Float) INT_MAX(As Float) - - Device temperature in degrees Celsius (C). It is measured at the location selected by DeviceTemperatureSelector. (C)
mvDeviceTemperatureState - - - Normal,
Critical,
OverTemperature
 Indicates the current temperature state of the device Normal: Indicates the current temperature state of the device Critical: Indicates the current temperature state of the device OverTemperature: Indicates the current temperature state of the device
mvDeviceTemperatureStateCriticalThreshold 50 90 1 - If the temperature of the device exceeds this value mvTemperatureState switches from normal to critical
mvDeviceFanState - - - Running,
NotRunning
 Indicates the state of the fan Running: Indicates the state of the fan NotRunning: Indicates the state of the fan
mvDeviceFanEnable - - - 0,
1
 Enable or disable cooling fan.
mvDeviceOperationMode - - - Rescue,
FullyOperational
 Shows the current operation mode. Rescue: The device is running in rescue mode. See mvDeviceRescueModeReason for details. FullyOperational: The device is fully operational.
mvDeviceRescueModeReason - - - FirmwareUpdateFailed,
OtherError
 Indicates the reason of the rescue mode. FirmwareUpdateFailed: The device runs in rescue mode, due to an unsuccessful firmware update attempt. Another firmware update has to be done to leave rescue mode. OtherError: The device runs in rescue mode, due to an unknown error. Reset the device or update the firmware to leave rescue mode.
Feature Name Min Max Inc Valid Values Documentation
ImageFormatControl A category for Image Format Control features.
WidthMax INT_MIN INT_MAX 1 - Maximum width of the image (in pixels). The dimension is calculated after horizontal binning, decimation or any other function changing the horizontal dimension of the image.
HeightMax INT_MIN INT_MAX 1 - Maximum height of the image (in pixels). This dimension is calculated after vertical binning, decimation or any other function changing the vertical dimension of the image.
SensorWidth INT_MIN INT_MAX 1 - Effective width of the sensor in pixels.
SensorHeight INT_MIN INT_MAX 1 - Effective height of the sensor in pixels.
SensorPixelWidth -340282346638528859811704183484516925440.000 340282346638528859811704183484516925440.000 - - Physical size (pitch) in the x direction of a photo sensitive pixel unit. (um)
SensorPixelHeight -340282346638528859811704183484516925440.000 340282346638528859811704183484516925440.000 - - Physical size (pitch) in the y direction of a photo sensitive pixel unit. (um)
SensorName - - - - Product name of the imaging Sensor.
Width 624 2464 16 - Width of the image provided by the device (in pixels).
Height 16 2064 16 - Height of the image provided by the device (in pixels).
OffsetX 0 0 16 - Horizontal offset from the origin to the region of interest (in pixels).
OffsetY 0 0 16 - Vertical offset from the origin to the region of interest (in pixels).
mvMultiAreaMode - - - mvOff,
mvMultiAreasCombined
 Selects the overall multi area mode. mvOff: Multi area mode is altogether switched off. Only one single AOI as defined in Width, Height, OffsetX and OffsetY properties is used and valid. mvMultiAreasCombined: Image is combined from multiple areas. The overlapping of areas is allowed. The camera decides which areas it needs to crop from the image and combines all areas into one image.
mvAreaSelector - - - mvArea0,
mvArea1,
mvArea2,
mvArea3,
mvArea4,
mvArea5,
mvArea6,
mvArea7
 Selects the area in multi area context. mvArea0: First area in multi area context. mvArea1: Second area in multi area context. mvArea2: Third area in multi area context. mvArea3: Fourth area in multi area context. mvArea4: Fifth area in multi area context. mvArea5: Sixth area in multi area context. mvArea6: Seventh area in multi area context. mvArea7: Eighth area in multi area context.
mvAreaEnable - - - 0,
1
 This feature controls whether the selected area is active during streaming or not.
mvAreaWidth INT64_MIN INT64_MAX 1 - Width of this area's part of the image (in pixels).
mvAreaHeight INT64_MIN INT64_MAX 1 - Height of this area's part of the image (in pixels).
mvAreaOffsetX INT64_MIN INT64_MAX 1 - Horizontal offset of this area within the image (in pixels).
mvAreaOffsetY INT64_MIN INT64_MAX 1 - Vertical offset of this area within the image (in pixels).
mvAreaResultingOffsetX INT64_MIN INT64_MAX 1 - Horizontal offset of this area within the resulting image (in pixels).
mvAreaResultingOffsetY INT64_MIN INT64_MAX 1 - Vertical offset of this area within the resulting image (in pixels).
mvAreaResultingHorizontalIndex INT64_MIN INT64_MAX 1 - Resulting horizontal area index
mvAreaResultingVerticalIndex INT64_MIN INT64_MAX 1 - Resulting vertical area index.
PixelFormat - - - BayerRG8,
BayerRG16,
RGB8,
BGR8,
BGRa8,
YUV422_8,
YUV422_8_UYVY,
YUV8_UYV,
BayerRG12p
 Format of the pixels provided by the device. It represents all the information provided by PixelSize, PixelColorFilter combined in a single feature. BayerRG8: Bayer Red Green 8 bit. BayerRG16: Bayer Red Green 16 bit. RGB8: Red, Green, Blue 8 bit BGR8: Blue, Green, Red, 8 bit. BGRa8: Blue, Green, Red, Alpha 8 bit. YUV422_8: YUV 422 8 bit. YUV422_8_UYVY: Format of the pixels provided by the device. YUV8_UYV: Format of the pixels provided by the device. BayerRG12p: Format of the pixels provided by the device.
mvSensorDigitizationBitDepth - - - Auto,
Bpp10,
Bpp12
 This feature manually selects the resolution of the device's ADC. Auto: When the selected pixel format has 12 bits or more the ADC will work with 12 bits. Otherwise the ADC will work with 10 bits. Bpp10: The ADC will always work with a resolution of 10 bits no matter which pixel format has been selected. Bpp12: The ADC will always work with a resolution of 12 bits no matter which pixel format has been selected. This will allow to achieve higher precision and thus improved quality when internal processing is done (e.g. when applying digital gain to the image).
TestPattern - - - Off,
mvBayerRaw
 Selects the type of test pattern that is generated by the device as image source. Off: Image is coming from the sensor. mvBayerRaw: Selects the type of test pattern that is generated by the device as image source.
TestImageSelector - - - Off,
mvBayerRaw
 This feature is deprecated (See TestPattern). Selects the type of test image that is sent by the device. Off: Image is coming from the sensor. mvBayerRaw: This feature is deprecated (See TestPattern).
BinningHorizontalMode - - - Sum,
Average
 Sets the mode to use to combine horizontal photo-sensitive cells together when BinningHorizontal is used. Sum: The response from the combined cells will be added, resulting in increased sensitivity. Average: The response from the combined cells will be averaged, resulting in increased signal/noise ratio.
BinningHorizontal 1 16 1 - Number of horizontal photo-sensitive cells to combine together. This reduces the horizontal resolution (width) of the image. Please note that most devices will only support values that are a power of 2 here, thus 1, 2, 4, 8 and so on up to the maximum value of the feature.
BinningVerticalMode - - - Sum,
Average
 Sets the mode to use to combine vertical photo-sensitive cells together when BinningVertical is used. Sum: The response from the combined cells will be added, resulting in increased sensitivity. Average: The response from the combined cells will be averaged, resulting in increased signal/noise ratio.
BinningVertical 1 16 1 - Number of vertical photo-sensitive cells to combine together. This reduces the vertical resolution (height) of the image. Please note that most devices will only support values that are a power of 2 here, thus 1, 2, 4, 8 and so on up to the maximum value of the feature.
DecimationHorizontalMode - - - Discard,
Average
 Sets the mode used to reduce the horizontal resolution when DecimationHorizontal is used. Discard: The value of every Nth pixel is kept, others are discarded. Average: The values of a group of N adjacent pixels are averaged.
DecimationHorizontal 1 16 1 - Horizontal sub-sampling of the image. This reduces the horizontal resolution (width) of the image by the specified horizontal decimation factor. Please note that most devices will only support values that are a power of 2 here, thus 1, 2, 4, 8 and so on up to the maximum value of the feature.
DecimationVerticalMode - - - Discard,
Average
 Sets the mode used to reduce the Vertical resolution when DecimationVertical is used. Discard: The value of every Nth pixel is kept, others are discarded. Average: The values of a group of N adjacent pixels are averaged.
DecimationVertical 1 16 1 - Vertical sub-sampling of the image. This reduces the vertical resolution (height) of the image by the specified vertical decimation factor. Please note that most devices will only support values that are a power of 2 here, thus 1, 2, 4, 8 and so on up to the maximum value of the feature.
ReverseX - - - 0,
1
 Flip horizontally the image sent by the device. The Region of interest is applied after the flipping.
ReverseY - - - 0,
1
 Flip vertically the image sent by the device. The Region of interest is applied after the flipping.
PixelColorFilter - - - None,
BayerRG,
BayerGB,
BayerGR,
BayerBG
 Type of color filter that is applied to the image. None: No color filter. BayerRG: Bayer Red Green filter. BayerGB: Bayer Green Blue filter. BayerGR: Bayer Green Red filter. BayerBG: Bayer Blue Green filter.
ImageCompressionQuality INT64_MIN INT64_MAX 1 - Control the quality of the produced compressed stream.
mvDualAdcMode - - - 0,
1
 Use this mode for a higher dynamic range. The maximum frame rate will be halved then. Using this mode only makes sense when used with pixel formats >= 14 bits. For Sony Gen 4 sensors, both high and low level gain pixels are combined internally in the sensor.
mvDualAdcCompression INT64_MIN INT64_MAX 1 - After the internal combination of both high and low gain pixels, the output data is compressed to fit 12-bits. This feature sets the compression characteristic of the Dual Adc (different kneepoints of the compression curve). 0 means compression is off.
Feature Name Min Max Inc Valid Values Documentation
AcquisitionControl A category for the acquisition and trigger control features.
AcquisitionMode - - - Continuous,
MultiFrame,
SingleFrame
 Sets the acquisition mode of the device. It defines mainly the number of frames to capture during an acquisition and the way the acquisition stops. Continuous: Frames are captured continuously until stopped with the AcquisitionStop command. MultiFrame: The number of frames specified by AcquisitionFrameCount is captured. SingleFrame: One frame is captured.
ExposureMode - - - Timed,
TriggerWidth
 Sets the operation mode of the Exposure. Timed: Timed exposure. The exposure duration time is set using the ExposureTime or ExposureAuto features and the exposure starts with the FrameStart or LineStart. TriggerWidth: Uses the width of the current Frame or Line trigger signal(s) pulse to control the exposure duration. Note that if the Frame or Line TriggerActivation is RisingEdge or LevelHigh, the exposure duration will be the time the trigger stays High. If TriggerActivation is FallingEdge or LevelLow, the exposure time will last as long as the trigger stays Low.
mvShutterMode - - - mvGlobalShutter,
mvPivShutter
 Selects the shutter mode of the sensor. mvGlobalShutter: Selects the shutter mode of the sensor. mvPivShutter: In this mode an image pair per trigger will be shot to allow PIV.
ExposureTime 10.000 20000000.000 - - Sets the Exposure time when ExposureMode is Timed and ExposureAuto is Off. This controls the duration where the photosensitive cells are exposed to light. (us)
ExposureAuto - - - Off,
Continuous
 Sets the automatic exposure mode when ExposureMode is Timed. The exact algorithm used to implement this control is device specific. Further settings can be controlled in the mvAutoFeatureControl. Off: Exposure duration is user controlled using ExposureTime. Continuous: Exposure duration is constantly adapted by the device to maximize the dynamic range.
mvExposureAutoLowerLimit -DBL_MAX DBL_MAX - - The lower limit of the exposure time in auto exposure mode.
mvExposureAutoUpperLimit -DBL_MAX DBL_MAX - - The upper limit of the exposure time in auto exposure mode.
mvExposureAutoAverageGrey INT64_MIN INT64_MAX 1 - Common desired average grey value (in percent) used for Auto Gain Control(AGC) and Auto Exposure Control(AEC).
mvExposureAutoHighlightAOI - - - Off,
On
 Highlight auto control AOI to check AOI settings. Switch off for normal operation. Off: Highlight auto control AOI to check AOI settings. Switch off for normal operation. On: Highlight auto control AOI to check AOI settings. Switch off for normal operation.
mvExposureAutoAOIMode - - - mvFull,
mvCenter,
mvUser
 Common AutoControl AOI used for Auto Gain Control(AGC), Auto Exposure Control(AEC) and Auto White Balancing. mvFull: Common AutoControl AOI used for Auto Gain Control(AGC), Auto Exposure Control(AEC) and Auto White Balancing. mvCenter: Common AutoControl AOI used for Auto Gain Control(AGC), Auto Exposure Control(AEC) and Auto White Balancing. mvUser: Common AutoControl AOI used for Auto Gain Control(AGC), Auto Exposure Control(AEC) and Auto White Balancing.
mvExposureAutoPrioritization - - - mvLowGain,
mvShortExposure
 selects the prioritization between exposure and gain controller. mvLowGain: selects the prioritization between exposure and gain controller. mvShortExposure: selects the prioritization between exposure and gain controller.
mvExposureAutoSensitivity INT64_MIN INT64_MAX 1 - The sensitivity of brightness deviations of the internal controller.
mvExposureAutoOffsetX INT64_MIN INT64_MAX 1 - Common AOI X-Offset used for Auto Gain Control(AGC), Auto Exposure Control(AEC) and Auto White Balance(AWB).
mvExposureAutoOffsetY INT64_MIN INT64_MAX 1 - Common AOI Y-Offset used for Auto Gain Control(AGC), Auto Exposure Control(AEC) and Auto White Balance(AWB).
mvExposureAutoWidth INT64_MIN INT64_MAX 1 - Common AOI Width used for Auto Gain Control(AGC), Auto Exposure Control(AEC) and Auto White Balance(AWB).
mvExposureAutoHeight INT64_MIN INT64_MAX 1 - Common AOI Height used for Auto Gain Control(AGC), Auto Exposure Control(AEC) and Auto White Balance(AWB).
TriggerSelector - - - FrameStart,
AcquisitionStart,
AcquisitionEnd,
AcquisitionActive,
mvTimestampReset,
FrameBurstStart,
FrameBurstActive
 Selects the type of trigger to configure. FrameStart: Selects a trigger starting the capture of one frame. AcquisitionStart: Selects a trigger that starts the Acquisition of one or many frames according to AcquisitionMode. AcquisitionEnd: Selects a trigger that ends the Acquisition of one or many frames according to AcquisitionMode. AcquisitionActive: Selects a trigger that controls the duration of the Acquisition of one or many frames. The Acquisition is activated when the trigger signal becomes active and terminated when it goes back to the inactive state. mvTimestampReset: Selects the type of trigger to configure. FrameBurstStart: Selects a trigger starting the capture of the bursts of frames in an acquisition. AcquisitionBurstFrameCount controls the length of each burst unless a FrameBurstEnd trigger is active. The total number of frames captured is also conditioned by AcquisitionFrameCount if AcquisitionMode is MultiFrame. FrameBurstActive: Selects a trigger controlling the duration of the capture of the bursts of frames in an acquisition.
TriggerMode - - - Off,
On
 Controls if the selected trigger is active. Off: Disables the selected trigger. On: Enable the selected trigger.
TriggerSource - - - Line4,
Line5,
Line6,
Line7,
Line8,
Line9,
Line10,
Line11,
Timer1Start,
Timer2Start,
Timer1End,
Timer2End,
Timer1Active,
Timer2Active,
Action1,
Action2,
Action3,
Action4,
UserOutput0,
UserOutput1,
UserOutput2,
UserOutput3,
Counter1End,
Counter2End,
Counter3End,
Counter4End,
Counter1Active,
Counter2Active,
Counter3Active,
Counter4Active,
mvCyclicSignal,
Software,
Off
 Specifies the internal signal or physical input Line to use as the trigger source. The selected trigger must have its TriggerMode set to On. Line4: Specifies which physical line (or pin) and associated I/O control block to use as external source for the trigger signal. Line5: Specifies which physical line (or pin) and associated I/O control block to use as external source for the trigger signal. Line6: Specifies which physical line (or pin) and associated I/O control block to use as external source for the trigger signal. Line7: Specifies which physical line (or pin) and associated I/O control block to use as external source for the trigger signal. Line8: Specifies which physical line (or pin) and associated I/O control block to use as external source for the trigger signal. Line9: Specifies which physical line (or pin) and associated I/O control block to use as external source for the trigger signal. Line10: Specifies which physical line (or pin) and associated I/O control block to use as external source for the trigger signal. Line11: Specifies which physical line (or pin) and associated I/O control block to use as external source for the trigger signal. Timer1Start: Specifies which Timer signal to use as internal source for the trigger. Timer2Start: Specifies which Timer signal to use as internal source for the trigger. Timer1End: Specifies which Timer signal to use as internal source for the trigger. Timer2End: Specifies which Timer signal to use as internal source for the trigger. Timer1Active: Triggers when the specified TriggerActivation condition is met on the chosen timer. Timer2Active: Triggers when the specified TriggerActivation condition is met on the chosen timer. Action1: Specifies which Action command to use as internal source for the trigger. Action2: Specifies which Action command to use as internal source for the trigger. Action3: Specifies which Action command to use as internal source for the trigger. Action4: Specifies which Action command to use as internal source for the trigger. UserOutput0: Specifies which User Output bit signal to use as internal source for the trigger. UserOutput1: Specifies which User Output bit signal to use as internal source for the trigger. UserOutput2: Specifies which User Output bit signal to use as internal source for the trigger. UserOutput3: Specifies which User Output bit signal to use as internal source for the trigger. Counter1End: Specifies which of the Counter signal to use as internal source for the trigger. Counter2End: Specifies which of the Counter signal to use as internal source for the trigger. Counter3End: Specifies which of the Counter signal to use as internal source for the trigger. Counter4End: Specifies which of the Counter signal to use as internal source for the trigger. Counter1Active: Triggers when the specified TriggerActivation condition is met on the chosen counter. Counter2Active: Triggers when the specified TriggerActivation condition is met on the chosen counter. Counter3Active: Triggers when the specified TriggerActivation condition is met on the chosen counter. Counter4Active: Triggers when the specified TriggerActivation condition is met on the chosen counter. mvCyclicSignal: Allows periodic trigger based on the timestamp modulo period calculation. Software: Specifies that the trigger source will be generated by software using the TriggerSoftware command. Off: No trigger source is selected.
TriggerActivation - - - RisingEdge,
FallingEdge,
AnyEdge
 Specifies the activation mode of the trigger. RisingEdge: Specifies that the trigger is considered valid on the rising edge of the source signal. FallingEdge: Specifies that the trigger is considered valid on the falling edge of the source signal. AnyEdge: Specifies that the trigger is considered valid on the falling or rising edge of the source signal.
TriggerDelay 0.000 UINT_MAX - - Specifies the delay in microseconds (us) to apply after the trigger reception before activating it. (us)
TriggerSoftware@i - - - - Generates an internal trigger. TriggerSource must be set to Software.
AcquisitionStart@i - - - - Starts the Acquisition of the device. The number of frames captured is specified by AcquisitionMode.
AcquisitionStop@i - - - - Stops the Acquisition of the device at the end of the current Frame. It is mainly used when AcquisitionMode is Continuous but can be used in any acquisition mode.
mvAcquisitionFrameRateLimitMode - - - mvDeviceLinkThroughput,
mvDeviceMaxSensorThroughput
 Controls the calculation of the maximum frame rate. mvDeviceLinkThroughput: Uses the highest possible frame rate depending on bandwidth and sensor settings. mvDeviceMaxSensorThroughput: Maximum frame rate the sensor can provide depending on AOI and pixel clock. Note: Images might be buffered in the cameras memory. This can result in delayed images.
AcquisitionFrameRateEnable - - - 0,
1
 Controls if the AcquisitionFrameRate feature is writable and used to control the acquisition rate. Otherwise, the acquisition rate is implicitly controlled by the combination of other features like ExposureTime, etc...
mvAcquisitionFrameRateEnable - - - Off,
On
 This feature is deprecated (See AcquisitionFrameRateEnable). It was used to enable the 'AcquisitionFrameRate' feature. Off: The acquisition frame rate is set automatically to the limit, calculated according to 'mvAcquisitionFrameRateLimitMode' feature. On: The acquisition frame rate is set by the 'AcquisitionFrameRate' feature.
AcquisitionFrameRate -DBL_MAX DBL_MAX - - Controls the acquisition rate (in Hertz) at which the frames are captured. (Hz)
AcquisitionFrameCount 1 65534 1 - Number of frames to acquire in MultiFrame Acquisition mode.
mvAcquisitionMemoryMode - - - Default,
mvRecord,
mvPlayback,
mvPretrigger
 mvRecord is used to store frames in memory. mvPlayback transfers stored frames. mvPretrigger stores frames in memory to be transferred after trigger. Default: Default memory mode. mvRecord: Stores frames in memory. mvPlayback: Transfers stored frames. mvPretrigger: Stores frames in memory to be transferred after trigger.
mvPretriggerFrameCount INT64_MIN INT64_MAX 1 - Number of frames to acquire before the occurrence of an AcquisitionStart or AcquisitionActive trigger.
mvAcquisitionMemoryMaxFrameCount INT_MIN INT_MAX 1 - Maximum number of frames that can be recorded in the current configuration.
mvAcquisitionMemoryFrameCount 0 280 1 - The number of frames currently stored in the frame buffer. If this value keeps increasing this can indicate a bandwidth/transmission problem.
mvAcquisitionMemoryAOIParameterChanged INT_MIN INT_MAX 1 - AOI and/or binning parameter changed after last Acquisition.
AcquisitionBurstFrameCount INT64_MIN INT64_MAX 1 - Number of frames to acquire for each FrameBurstStart trigger.
mvResultingFrameRate INT_MIN(As Float) INT_MAX(As Float) - - Shows the resulting frame rate.
Feature Name Min Max Inc Valid Values Documentation
CounterAndTimerControl A category that contains the Counter and Timer control features.
CounterSelector - - - Counter1,
Counter2,
Counter3,
Counter4
 Selects which Counter to configure. Counter1: Selects the counter 1. Counter2: Selects the counter 2. Counter3: Selects the counter 3. Counter4: Selects the counter 4.
CounterEventSource - - - Off,
AcquisitionStart,
AcquisitionEnd,
FrameStart,
FrameEnd,
ExposureStart,
ExposureEnd,
Line4,
Line5,
Line6,
Line7,
Line8,
Line9,
Line10,
Line11,
Counter1End,
Counter2End,
Counter3End,
Counter4End,
Timer1End,
Timer2End,
Action1,
Action2,
Action3,
Action4,
TimestampTick,
LineStart,
UserOutput0,
UserOutput1,
UserOutput2,
UserOutput3,
mvCyclicSignal
 Select the events that will be the source to increment the Counter. Off: Counter is stopped. AcquisitionStart: Counts the number of Acquisition Start. AcquisitionEnd: Counts the number of Acquisition End. FrameStart: Counts the number of Frame Start. FrameEnd: Counts the number of Frame End. ExposureStart: Counts the number of Exposure Start. ExposureEnd: Counts the number of Exposure End. Line4: Counts the number of transitions on the chosen I/O Line. Line5: Counts the number of transitions on the chosen I/O Line. Line6: Counts the number of transitions on the chosen I/O Line. Line7: Counts the number of transitions on the chosen I/O Line. Line8: Counts the number of transitions on the chosen I/O Line. Line9: Counts the number of transitions on the chosen I/O Line. Line10: Counts the number of transitions on the chosen I/O Line. Line11: Counts the number of transitions on the chosen I/O Line. Counter1End: Counts the number of Counter End. Counter2End: Counts the number of Counter End. Counter3End: Counts the number of Counter End. Counter4End: Counts the number of Counter End. Timer1End: Counts the number of Timer End pulses generated. Timer2End: Counts the number of Timer End pulses generated. Action1: Counts the number of assertions of the chosen action signal. Action2: Counts the number of assertions of the chosen action signal. Action3: Counts the number of assertions of the chosen action signal. Action4: Counts the number of assertions of the chosen action signal. TimestampTick: Counts the number of clock ticks of the Timestamp clock. Can be used to create a programmable timer. LineStart: Counts the number of Line Start. UserOutput0: Select the events that will be the source to increment the Counter. UserOutput1: Select the events that will be the source to increment the Counter. UserOutput2: Select the events that will be the source to increment the Counter. UserOutput3: Select the events that will be the source to increment the Counter. mvCyclicSignal: Allows periodic trigger based on the timestamp modulo period calculation.
CounterEventActivation - - - RisingEdge,
FallingEdge,
AnyEdge
 Selects the Activation mode Event Source signal. RisingEdge: Counts on the Rising Edge of the signal. FallingEdge: Counts on the Falling Edge of the signal. AnyEdge: Counts on the Falling or rising Edge of the selected signal.
CounterResetSource - - - Off,
AcquisitionStart,
AcquisitionEnd,
FrameStart,
FrameEnd,
ExposureStart,
ExposureEnd,
Line4,
Line5,
Line6,
Line7,
Line8,
Line9,
Line10,
Line11,
Counter1End,
Counter2End,
Counter3End,
Counter4End,
Timer1End,
Timer2End,
Action1,
Action2,
Action3,
Action4,
UserOutput0,
UserOutput1,
UserOutput2,
UserOutput3,
mvCyclicSignal
 Selects the signals that will be the source to reset the Counter. Off: Disable the Counter Reset trigger. AcquisitionStart: Resets with the reception of the Acquisition Start. AcquisitionEnd: Resets with the reception of the Acquisition End. FrameStart: Resets with the reception of the Frame Start. FrameEnd: Resets with the reception of the Frame End. ExposureStart: Resets with the reception of the Exposure Start. ExposureEnd: Resets with the reception of the Exposure End. Line4: Resets by the chosen I/O Line. Line5: Resets by the chosen I/O Line. Line6: Resets by the chosen I/O Line. Line7: Resets by the chosen I/O Line. Line8: Resets by the chosen I/O Line. Line9: Resets by the chosen I/O Line. Line10: Resets by the chosen I/O Line. Line11: Resets by the chosen I/O Line. Counter1End: Resets with the reception of the Counter End. Counter2End: Resets with the reception of the Counter End. Counter3End: Resets with the reception of the Counter End. Counter4End: Resets with the reception of the Counter End. Timer1End: Resets with the reception of the Timer End. Timer2End: Resets with the reception of the Timer End. Action1: Resets on assertions of the chosen action signal (Broadcasted signal on the transport layer). Action2: Resets on assertions of the chosen action signal (Broadcasted signal on the transport layer). Action3: Resets on assertions of the chosen action signal (Broadcasted signal on the transport layer). Action4: Resets on assertions of the chosen action signal (Broadcasted signal on the transport layer). UserOutput0: Resets by the chosen User Output bit. UserOutput1: Resets by the chosen User Output bit. UserOutput2: Resets by the chosen User Output bit. UserOutput3: Resets by the chosen User Output bit. mvCyclicSignal: Allows periodic trigger based on the timestamp modulo period calculation.
CounterResetActivation - - - RisingEdge,
FallingEdge,
AnyEdge,
LevelHigh,
LevelLow
 Selects the Activation mode of the Counter Reset Source signal. RisingEdge: Resets the counter on the Rising Edge of the signal. FallingEdge: Resets the counter on the Falling Edge of the signal. AnyEdge: Resets the counter on the Falling or rising Edge of the selected signal. LevelHigh: Resets the counter as long as the selected signal level is High. LevelLow: Resets the counter as long as the selected signal level is Low.
CounterTriggerSource - - - Off,
AcquisitionStart,
AcquisitionEnd,
FrameStart,
FrameEnd,
ExposureStart,
ExposureEnd,
Line4,
Line5,
Line6,
Line7,
Line8,
Line9,
Line10,
Line11,
Counter1End,
Counter2End,
Counter3End,
Counter4End,
Timer1End,
Timer2End,
Action1,
Action2,
Action3,
Action4,
mvReadOutActive,
ExposureActive,
UserOutput0,
UserOutput1,
UserOutput2,
UserOutput3,
mvCyclicSignal
 Selects the source to start the Counter. Off: Disables the Counter trigger. AcquisitionStart: Starts with the reception of the Acquisition Start. AcquisitionEnd: Starts with the reception of the Acquisition End. FrameStart: Starts with the reception of the Frame Start. FrameEnd: Starts with the reception of the Frame End. ExposureStart: Starts with the reception of the Exposure Start. ExposureEnd: Starts with the reception of the Exposure End. Line4: Starts when the specified CounterTriggerActivation condition is met on the chosen I/O Line. Line5: Starts when the specified CounterTriggerActivation condition is met on the chosen I/O Line. Line6: Starts when the specified CounterTriggerActivation condition is met on the chosen I/O Line. Line7: Starts when the specified CounterTriggerActivation condition is met on the chosen I/O Line. Line8: Starts when the specified CounterTriggerActivation condition is met on the chosen I/O Line. Line9: Starts when the specified CounterTriggerActivation condition is met on the chosen I/O Line. Line10: Starts when the specified CounterTriggerActivation condition is met on the chosen I/O Line. Line11: Starts when the specified CounterTriggerActivation condition is met on the chosen I/O Line. Counter1End: Starts with the reception of the Counter End. Counter2End: Starts with the reception of the Counter End. Counter3End: Starts with the reception of the Counter End. Counter4End: Starts with the reception of the Counter End. Timer1End: Starts with the reception of the Timer End. Timer2End: Starts with the reception of the Timer End. Action1: Starts with the assertion of the chosen action signal. Action2: Starts with the assertion of the chosen action signal. Action3: Starts with the assertion of the chosen action signal. Action4: Starts with the assertion of the chosen action signal. mvReadOutActive: Starts when the specified CounterTriggerActivation condition is met on the sensor's readout signal. ExposureActive: Starts when the specified CounterTriggerActivation condition is met on the exposure signal. UserOutput0: Specifies which User Output bit signal to use as internal source for the trigger. UserOutput1: Specifies which User Output bit signal to use as internal source for the trigger. UserOutput2: Specifies which User Output bit signal to use as internal source for the trigger. UserOutput3: Specifies which User Output bit signal to use as internal source for the trigger. mvCyclicSignal: Allows periodic trigger based on the timestamp modulo period calculation.
CounterTriggerActivation - - - RisingEdge,
FallingEdge,
AnyEdge,
LevelHigh,
LevelLow
 Selects the activation mode of the trigger to start the Counter. RisingEdge: Starts counting on the Rising Edge of the selected trigger signal. FallingEdge: Starts counting on the Falling Edge of the selected trigger signal. AnyEdge: Starts counting on the Falling or rising Edge of the selected trigger signal. LevelHigh: Counts as long as the selected trigger signal level is High. LevelLow: Counts as long as the selected trigger signal level is Low.
CounterDuration 0 UINT_MAX 1 - Sets the duration (or number of events) before the CounterEnd event is generated.
CounterValue 0 UINT_MAX 1 - Reads or writes the current value of the selected Counter.
CounterValueAtReset 0 UINT_MAX 1 - Reads the value of the selected Counter when it was reset by a trigger or by an explicit CounterReset command.
CounterReset@i - - - - Does a software reset of the selected Counter and starts it. The counter starts counting events immediately after the reset unless a Counter trigger is active. CounterReset can be used to reset the Counter independently from the CounterResetSource. To disable the counter temporarily, set CounterEventSource to Off.
TimerSelector - - - Timer1,
Timer2
 Selects which Timer to configure. Timer1: Selects the Timer 1. Timer2: Selects the Timer 2.
TimerTriggerSource - - - Off,
AcquisitionStart,
AcquisitionEnd,
FrameStart,
FrameEnd,
ExposureStart,
ExposureEnd,
Line4,
Line5,
Line6,
Line7,
Line8,
Line9,
Line10,
Line11,
Counter1End,
Counter2End,
Counter3End,
Counter4End,
Timer1End,
Timer2End,
Action1,
Action2,
Action3,
Action4,
UserOutput0,
UserOutput1,
UserOutput2,
UserOutput3,
mvCyclicSignal
 Selects the source of the trigger to start the Timer. Off: Disables the Timer trigger. AcquisitionStart: Starts with the reception of the Acquisition Start. AcquisitionEnd: Starts with the reception of the Acquisition End. FrameStart: Starts with the reception of the Frame Start. FrameEnd: Starts with the reception of the Frame End. ExposureStart: Starts with the reception of the Exposure Start. ExposureEnd: Starts with the reception of the Exposure End. Line4: Starts when the specified TimerTriggerActivation condition is met on the chosen I/O Line. Line5: Starts when the specified TimerTriggerActivation condition is met on the chosen I/O Line. Line6: Starts when the specified TimerTriggerActivation condition is met on the chosen I/O Line. Line7: Starts when the specified TimerTriggerActivation condition is met on the chosen I/O Line. Line8: Starts when the specified TimerTriggerActivation condition is met on the chosen I/O Line. Line9: Starts when the specified TimerTriggerActivation condition is met on the chosen I/O Line. Line10: Starts when the specified TimerTriggerActivation condition is met on the chosen I/O Line. Line11: Starts when the specified TimerTriggerActivation condition is met on the chosen I/O Line. Counter1End: Starts with the reception of the Counter End. Counter2End: Starts with the reception of the Counter End. Counter3End: Starts with the reception of the Counter End. Counter4End: Starts with the reception of the Counter End. Timer1End: Starts with the reception of the Timer End. Note that a timer can retrigger itself to achieve a free running Timer. Timer2End: Starts with the reception of the Timer End. Note that a timer can retrigger itself to achieve a free running Timer. Action1: Starts with the assertion of the chosen action signal. Action2: Starts with the assertion of the chosen action signal. Action3: Starts with the assertion of the chosen action signal. Action4: Starts with the assertion of the chosen action signal. UserOutput0: Specifies which User Output bit signal to use as internal source for the trigger. UserOutput1: Specifies which User Output bit signal to use as internal source for the trigger. UserOutput2: Specifies which User Output bit signal to use as internal source for the trigger. UserOutput3: Specifies which User Output bit signal to use as internal source for the trigger. mvCyclicSignal: Allows periodic trigger based on the timestamp modulo period calculation.
TimerTriggerActivation - - - RisingEdge,
FallingEdge,
AnyEdge,
LevelHigh,
LevelLow
 Selects the activation mode of the trigger to start the Timer. RisingEdge: Starts counting on the Rising Edge of the selected trigger signal. FallingEdge: Starts counting on the Falling Edge of the selected trigger signal. AnyEdge: Starts counting on the Falling or Rising Edge of the selected trigger signal. LevelHigh: Counts as long as the selected trigger signal level is High. LevelLow: Counts as long as the selected trigger signal level is Low.
TimerDuration 0.000 UINT_MAX - - Sets the duration (in microseconds) of the Timer pulse. (us)
TimerDelay 0.000 UINT_MAX - - Sets the duration (in microseconds) of the delay to apply at the reception of a trigger before starting the Timer. (us)
TimerValue 0.000 UINT_MAX - - Reads or writes the current value (in microseconds) of the selected Timer. (us)
TimerReset@i - - - - Does a software reset of the selected timer and starts it. The timer starts immediately after the reset unless a timer trigger is active.
Feature Name Min Max Inc Valid Values Documentation
AnalogControl A category that contains the Analog control features.
mvTapBalancingMode - - - mvFactory,
mvUser
 States where the tap balancing calibration data does come from mvFactory: States where the tap balancing calibration data does come from mvUser: States where the tap balancing calibration data does come from
mvGainMode - - - Default
 Sets the operation mode of Gain Default: Default operation mode. The whole image is configured as a single zone.
GainSelector - - - AnalogAll
 Selects which Gain is controlled by the various Gain features. AnalogAll: Gain will be applied to all analog channels or taps.
Gain 0.000 48.000 - - Controls the selected gain as an absolute physical value in dB. This is an amplification factor applied to the video signal. (dB)
GainAuto - - - Off,
Continuous
 Sets the automatic gain control (AGC) mode. The exact algorithm used to implement this control is device specific. Further settings can be controlled in the mvAutoFeatureControl. Off: Gain is User controlled using Gain. Continuous: Gain is constantly adjusted by the device.
mvGainAutoUpperLimit -DBL_MAX DBL_MAX - - The upper limit of the gain in auto gain mode.
mvGainAutoLowerLimit -DBL_MAX DBL_MAX - - The lower limit of the gain in auto gain mode.
mvGainAutoAverageGrey INT64_MIN INT64_MAX 1 - Common desired average grey value (in percent) used for Auto Gain Control(AGC) and Auto Exposure Control(AEC).
mvGainAutoHighlightAOI - - - Off,
On
 Highlight auto control AOI to check AOI settings. Switch off for normal operation. Off: Highlight auto control AOI to check AOI settings. Switch off for normal operation. On: Highlight auto control AOI to check AOI settings. Switch off for normal operation.
mvGainAutoAOIMode - - - mvFull,
mvCenter,
mvUser
 Common AutoControl AOI used for Auto Gain Control(AGC), Auto Exposure Control(AEC) and Auto White Balancing. mvFull: Common AutoControl AOI used for Auto Gain Control(AGC), Auto Exposure Control(AEC) and Auto White Balancing. mvCenter: Common AutoControl AOI used for Auto Gain Control(AGC), Auto Exposure Control(AEC) and Auto White Balancing. mvUser: Common AutoControl AOI used for Auto Gain Control(AGC), Auto Exposure Control(AEC) and Auto White Balancing.
mvGainAutoSensitivity INT64_MIN INT64_MAX 1 - The sensitivity of brightness deviations of the internal controller.
mvGainAutoOffsetX INT64_MIN INT64_MAX 1 - Common AOI X-Offset used for Auto Gain Control(AGC), Auto Exposure Control(AEC) and Auto White Balance(AWB).
mvGainAutoOffsetY INT64_MIN INT64_MAX 1 - Common AOI Y-Offset used for Auto Gain Control(AGC), Auto Exposure Control(AEC) and Auto White Balance(AWB).
mvGainAutoWidth INT64_MIN INT64_MAX 1 - Common AOI Width used for Auto Gain Control(AGC), Auto Exposure Control(AEC) and Auto White Balance(AWB).
mvGainAutoHeight INT64_MIN INT64_MAX 1 - Common AOI Height used for Auto Gain Control(AGC), Auto Exposure Control(AEC) and Auto White Balance(AWB).
BlackLevelSelector - - - All,
DigitalAll
 Selects which Black Level is controlled by the various Black Level features. All: Black Level will be applied to all channels or taps. DigitalAll: Selects which Black Level is controlled by the various Black Level features.
BlackLevel 0.000 100.000 - - Controls the analog black level as an absolute physical value. This represents a DC offset applied to the video signal.
BlackLevelAuto - - - Off,
Continuous
 Controls the mode for automatic black level adjustment. The exact algorithm used to implement this adjustment is device-specific. Off: Analog black level is user controlled using BlackLevel. Continuous: Analog black level is constantly adjusted by the device.
mvGammaEnable - - - 0,
1
 Enables gamma correction. All other LUT will be disabled.
mvGammaSelector - - - mvSRGB,
mvUser
 Sets the type of Gamma to be used. mvSRGB: Gamma is fixed to a sRGB curve. mvUser: Gamma can be configured by user.
Gamma -DBL_MAX DBL_MAX - - Controls the gamma correction of pixel intensity.
BalanceRatioSelector - - - Red,
Blue
 Selects which Balance ratio to control. Red: Balance Ratio will be applied to the red channel. Blue: Balance Ratio will be applied to the blue channel.
BalanceRatio 0.004 256.000 - - Controls ratio of the selected color component to a reference color component. It is used for white balancing.
BalanceWhiteAuto - - - Off,
Once,
Continuous
 Controls the mode for automatic white balancing between the color channels. The white balancing ratios are automatically adjusted. Further settings can be found in th mvAutoFeatureControl. Off: White balancing is user controlled using BalanceRatioSelector and BalanceRatio. Once: White balancing is automatically adjusted once by the device. Once it has converged, it automatically returns to the Off state. Continuous: White balancing is constantly adjusted by the device.
mvBalanceWhiteAutoAOIMode - - - mvFull,
mvCenter,
mvUser
 Common AutoControl AOI used for Auto Gain Control(AGC), Auto Exposure Control(AEC) and Auto White Balancing. mvFull: Common AutoControl AOI used for Auto Gain Control(AGC), Auto Exposure Control(AEC) and Auto White Balancing. mvCenter: Common AutoControl AOI used for Auto Gain Control(AGC), Auto Exposure Control(AEC) and Auto White Balancing. mvUser: Common AutoControl AOI used for Auto Gain Control(AGC), Auto Exposure Control(AEC) and Auto White Balancing.
mvBalanceWhiteAutoOffsetX INT64_MIN INT64_MAX 1 - Common AOI X-Offset used for Auto Gain Control(AGC), Auto Exposure Control(AEC) and Auto White Balance(AWB).
mvBalanceWhiteAutoOffsetY INT64_MIN INT64_MAX 1 - Common AOI Y-Offset used for Auto Gain Control(AGC), Auto Exposure Control(AEC) and Auto White Balance(AWB).
mvBalanceWhiteAutoWidth INT64_MIN INT64_MAX 1 - Common AOI Width used for Auto Gain Control(AGC), Auto Exposure Control(AEC) and Auto White Balance(AWB).
mvBalanceWhiteAutoHeight INT64_MIN INT64_MAX 1 - Common AOI Height used for Auto Gain Control(AGC), Auto Exposure Control(AEC) and Auto White Balance(AWB).
Feature Name Min Max Inc Valid Values Documentation
mvAutoFeatureControl Contains features to control the image controllers. The properties are applied to Auto Gain Control(AGC) and Auto Exposure Control(AEC) controller. To take effect at least AEC or AGC must be enabled.
mvAutoFeatureBrightness 0 100 1 - Common desired average brightness value (in percent) used for Auto Gain Control(AGC) and Auto Exposure Control(AEC). At least one of these controllers must be activated for the value to take effect.
mvAutoFeatureSensitivity 1 100 1 - The controllers sensitivity of brightness deviations. This parameter influences the gain as well as the exposure controller. At least one of these controllers must be activated for the value to take effect.
mvAutoFeatureCharacteristic - - - mvLowGain,
mvShortExposure
 Selects the prioritization between Auto Exposure Control(AEC) and Auto Gain Control(AGC) controller. Both controllers have to be activated before. mvLowGain: Selects the prioritization between Auto Exposure Control(AEC) and Auto Gain Control(AGC) controller. Both controllers have to be activated before. mvShortExposure: Selects the prioritization between Auto Exposure Control(AEC) and Auto Gain Control(AGC) controller. Both controllers have to be activated before.
mvAutoFeatureBrightnessCalculation - - - mvPeak,
mvAverage
 Selects the method to determine the brightness for Auto Exposure Control(AEC) and Auto Gain Control(AGC) controller. mvPeak: The peak brightness value is used as actual value for the controller. mvAverage: The average brightness is used as actual value for the controller.
mvAutoFeatureAOIHighlightEnable - - - Off,
On
 Highlight auto control AOI to check AOI settings. Switch off for normal operation. Off: The AutoFeatureAOIHighlight is switched off. On: The AutoFeatureAOIHighlight is switched on.
mvAutoFeatureAOIMode - - - mvFull,
mvCenter,
mvUser
 Common AutoControl AOI used for Auto Gain Control(AGC), Auto Exposure Control(AEC) and Auto White Balancing. mvFull: The auto controller uses the full frame for the actual value computation. mvCenter: The auto controller uses a centered AOI of 25% the full frame for the actual value computation. mvUser: The auto controller uses the user defined AOI for the actual value computation.
mvAutoFeatureAOIOffsetX INT64_MIN INT64_MAX 1 - Common AOI X-Offset used for Auto Gain Control(AGC), Auto Exposure Control(AEC) and Auto White Balance(AWB).
mvAutoFeatureAOIOffsetY INT64_MIN INT64_MAX 1 - Common AOI Y-Offset used for Auto Gain Control(AGC), Auto Exposure Control(AEC) and Auto White Balance(AWB).
mvAutoFeatureAOIWidth INT64_MIN INT64_MAX 1 - Common AOI Width used for Auto Gain Control(AGC), Auto Exposure Control(AEC) and Auto White Balance(AWB).
mvAutoFeatureAOIHeight INT64_MIN INT64_MAX 1 - Common AOI Height used for Auto Gain Control(AGC), Auto Exposure Control(AEC) and Auto White Balance(AWB).
mvAutoFeatureBrightnessTolerance 0 20 2 - The error input hysteresis gap of the controller. If the brightness error exceeds the half of the value in positive or negative direction, the controller restarts to control the brightness. This property applies to AEC and AGC as well.
Feature Name Min Max Inc Valid Values Documentation
mvSerialInterfaceControl Contains features to control the serial interface.
mvSerialInterfaceEnable - - - 0,
1
 Controls whether the serial interface is enabled or not.
mvSerialInterfaceMode - - - Plain,
InveniosLiquidLens,
OptoEngineeringStepper
 States the interface mode of the serial interface. Plain: The serial interface shall be used in 'plain' mode. InveniosLiquidLens: The serial interface shall be used to control an Invenios liquid lens. OptoEngineeringStepper: The serial interface shall be used to control an Opto Engineering Stepper.
mvSerialInterfaceBaudRate - - - Hz_115200,
Hz_57600,
Hz_38400,
Hz_19200,
Hz_9600
 Serial interface clock frequency. Hz_115200: Serial interface clock frequency. Hz_57600: Serial interface clock frequency. Hz_38400: Serial interface clock frequency. Hz_19200: Serial interface clock frequency. Hz_9600: Serial interface clock frequency.
mvSerialInterfaceDataBits - - - Eight
 Number of data bits. Eight: Number of data bits.
mvSerialInterfaceParity - - - None,
Odd,
Even
 Serial interface parity. None: Serial interface parity. Odd: Serial interface parity. Even: Serial interface parity.
mvSerialInterfaceStopBits - - - One,
Two
 Number of stop bits. One: Number of stop bits. Two: Number of stop bits.
mvSerialInterfaceASCIIBuffer - - - - Buffer for exchanging ASCII data over the serial interface. This buffer uses the same memory as 'mvSerialInterfaceBinaryBuffer'.
mvSerialInterfaceBinaryBuffer - - - - Buffer for exchanging binary data over the serial interface. This buffer uses the same memory as 'mvSerialInterfaceASCIIBuffer'.
mvSerialInterfaceBytesToWrite INT64_MIN INT64_MAX 1 - Length of data to write.
mvSerialInterfaceBytesAvailableForRead INT64_MIN INT64_MAX 1 - When refreshed number of available data bytes for read are shown.
mvSerialInterfaceReceiveStatus INT64_MIN INT64_MAX 0x1 - Result of the serial receive error detection mechanism. This is a bit field. The bits have the following meaning: 0x1: Receive Buffer Overflow, 0x2: Parity Error, 0x4: Framing Error, 0x8: Break Detect
mvSerialInterfaceBytesToRead INT64_MIN INT64_MAX 1 - Number of serial bytes to read (Note: After read command value is updated with real number of bytes read).
mvSerialInterfaceRead@i - - - - Command to read data from serial interface.
mvSerialInterfaceWrite@i - - - - Command to write data to serial interface
mvLiquidLensFirmwareVersion INT64_MIN INT64_MAX 0x1 - Returns the firmware version of the Liquid Lens.
mvLiquidLensStatus - - - NoError,
VhOverload,
ThermalOverload,
VhAndThermalOverload,
StatusReadErrorNoAnswer,
StatusReadErrorCRC,
StatusReadErrorNakAnswer,
StatusReadErrorInvalidAnswer
 Returns the current status of the Liquid Lens. NoError: No Errors. VhOverload: Vh below 70V because Liquid Lens is taking too much current. ThermalOverload: Driver shutdown because Liquid Lens is too hot. VhAndThermalOverload: Vh does not reach 70V and driver shutdown because Liquid Lens is too hot. StatusReadErrorNoAnswer: No response from Liquid Lens. StatusReadErrorCRC: CRC error in response from Liquid Lens. StatusReadErrorNakAnswer: NAK response from Liquid Lens. StatusReadErrorInvalidAnswer: Invalid Size or Command in response from Liquid Lens.
mvLiquidLensErrorCount INT64_MIN INT64_MAX 1 - This register increments whenever an error occurred while communicating with the Liquid Lens.
mvLiquidLensPowerMode - - - mvLiquidLensActive,
mvLiquidLensStandby
 Selects the device power mode. mvLiquidLensActive: Puts the device to power-active mode. mvLiquidLensStandby: Puts the Liquid Lens in power-saving mode. In this mode the device will only consume up to 25 percent of its normal power consumption.
mvLiquidLensSetFocusValue INT64_MIN INT64_MAX 1 - Focus position value for Liquid Lens.
mvLiquidLensSaveFocusValue@i - - - - Saves the current Focus position into LiquidLens EEPROM.
mvStepperFirmwareVersion INT64_MIN INT64_MAX 0x1 - Returns the firmware version of the Opto Engineering Stepper.
mvStepperReceiveStatus INT64_MIN INT64_MAX 0x1 - Result of the serial receive error detection mechanism. This is a bit field. The bits have the following meaning: 0x1: Reserved, 0x2: Mismatch in answer detected, 0x4: No response, 0x8 Incorrect answer received.
mvStepperErrorCount INT64_MIN INT64_MAX 1 - This register increments whenever an error occurred while communicating with the Opto Engineering Stepper.
mvStepperAutoSavePositionEnable - - - 0,
1
 Controls if the auto-save of motor positions is active.
mvStepperMotorSelector - - - Zoom,
Focus,
Iris
 Selects the stepper motor to control(Zoom, Iris or Focus). Zoom: Selects the stepper motor controlling the zoom. Focus: Selects the stepper motor controlling the focus. Iris: Selects the stepper motor controlling the iris.
mvStepperStatus - - - Unknown,
Moving,
StoppedAtLowerLimitWithTorque,
StoppedAtLowerLimit,
StoppedAtUpperLimitWithTorque,
StoppedAtUpperLimit,
StoppedWithTorque,
Stopped,
OvercurrentOrOvertemperatureError
 Returns the current status of the stepper. Unknown: The current status of the stepper is unknown. Moving: The selected stepper motor is currently moving. StoppedAtLowerLimitWithTorque: The selected stepper motor has stopped at its lower limit with torque(this should never happen and indicates a problem). StoppedAtLowerLimit: The selected stepper motor has stopped at its lower limit. StoppedAtUpperLimitWithTorque: The selected stepper motor has stopped at its upper limit with torque(this should never happen and indicates a problem). StoppedAtUpperLimit: The selected stepper motor has stopped at its upper limit. StoppedWithTorque: The selected stepper motor has stopped with torque(this should never happen and indicates a problem). Stopped: The selected stepper motor has stopped. OvercurrentOrOvertemperatureError: The selected stepper motor either became too hot or is taking in too much current(this should never happen and indicates a problem).
mvStepperCurrentPosition INT64_MIN INT64_MAX 1 - Read current position from stepper.
mvStepperDesiredPosition INT64_MIN INT64_MAX 1 - The desired position of the selected stepper motor. When the motor has not yet reached this position(is moving) this value may differ from 'mvStepperCurrentPosition'.
mvStepperSpeed -DBL_MAX DBL_MAX - - Current speed of the selected stepper motor.
mvStepperAcceleration -DBL_MAX DBL_MAX - - Current acceleration of the selected stepper motor.
mvStepperPositionSetSelector INT64_MIN INT64_MAX 1 - Selects the stepper parameter set to load or save.
mvStepperPositionSetLoad@i - - - - Loads the stepper 'mvStepperDesiredPosition' specified by 'mvStepperPositionSetSelector' and makes it active for each motor.
mvStepperPositionSetSave@i - - - - Saves the stepper 'mvStepperDesiredPosition' specified by 'mvStepperPositionSetSelector' into the steppers non-volatile memory for each motor.
mvStepperMoveToHomeAll@i - - - - Moves all stepper motors to their home position.
mvStepperStopAll@i - - - - Stops all stepper motors.
Feature Name Min Max Inc Valid Values Documentation
mvCustomData Contains features to control custom data.
mvExposureTimeError -340282346638528859811704183484516925440.000 340282346638528859811704183484516925440.000 - - Additive sensor error of the exposure time in us according to the sensor data sheet.
mvExposureTimeIncrement -340282346638528859811704183484516925440.000 340282346638528859811704183484516925440.000 - - Increment of the exposure time in us.
mvExposureStartDelay -340282346638528859811704183484516925440.000 340282346638528859811704183484516925440.000 - - Delay from sensor-trigger to actual exposure start in us.
Feature Name Min Max Inc Valid Values Documentation
FileAccessControl A category that contains the File Access control features.
FileSelector - - - DeviceFirmware
 Selects the target file in the device. DeviceFirmware: Selects the target file in the device.
FileOperationSelector - - - Open,
Close,
Read,
Write,
MvFlashWrite,
Delete
 Selects the target operation for the selected file in the device. This Operation is executed when the FileOperationExecute feature is called. Open: Opens the file selected by FileSelector in the device. The access mode in which the file is opened is selected by FileOpenMode. Close: Closes the file selected by FileSelector in the device. Read: Reads FileAccessLength bytes from the device storage at the file relative offset FileAccessOffset into FileAccessBuffer. Write: Writes FileAccessLength bytes taken from the FileAccessBuffer into the device storage at the file relative offset FileAccessOffset. MvFlashWrite: Selects the target operation for the selected file in the device. Delete: Deletes the file selected by FileSelector in the device. Note that deleting a device file should not remove the associated FileSelector entry to allow future operation on this file.
FileOperationExecute@i - - - - Executes the operation selected by FileOperationSelector on the selected file.
FileOpenMode - - - Read,
Write,
ReadWrite
 Selects the access mode in which a file is opened in the device. Read: This mode selects read-only open mode. Write: This mode selects write-only open mode. ReadWrite: This mode selects read and write open mode.
FileAccessBuffer - - - - Defines the intermediate access buffer that allows the exchange of data between the device file storage and the application.
FileAccessOffset 0 0 1 - Controls the Offset of the mapping between the device file storage and the FileAccessBuffer. (B)
FileAccessLength 0 536 1 - Controls the Length of the mapping between the device file storage and the FileAccessBuffer. (B)
FileOperationStatus - - - Success,
Failure
 Represents the file operation execution status. Success: File Operation was successful. Failure: File Operation failed.
FileOperationResult INT_MIN INT_MAX 1 - Represents the file operation result. For Read or Write operations, the number of successfully read/written bytes is returned.
FileSize INT_MIN INT_MAX 1 - Represents the size of the selected file in bytes. (B)
Feature Name Min Max Inc Valid Values Documentation
DigitalIOControl A category that contains the digital input and output control features.
LineSelector - - - Line0,
Line1,
Line2,
Line3,
Line4,
Line5,
Line6,
Line7,
Line8,
Line9,
Line10,
Line11
 Selects the physical line (or pin) of the external device connector or the virtual line of the Transport Layer to configure. Line0: Index of the physical line and associated I/O control block to use. Line1: Index of the physical line and associated I/O control block to use. Line2: Index of the physical line and associated I/O control block to use. Line3: Index of the physical line and associated I/O control block to use. Line4: Index of the physical line and associated I/O control block to use. Line5: Index of the physical line and associated I/O control block to use. Line6: Index of the physical line and associated I/O control block to use. Line7: Index of the physical line and associated I/O control block to use. Line8: Index of the physical line and associated I/O control block to use. Line9: Index of the physical line and associated I/O control block to use. Line10: Index of the physical line and associated I/O control block to use. Line11: Index of the physical line and associated I/O control block to use.
mvLineCaps INT_MIN INT_MAX 1 - Invisible
LineMode - - - Output
 Controls if the physical Line is used to Input or Output a signal. Output: The selected physical line is used to Output an electrical signal.
LineStatus - - - 0,
1
 Returns the current status of the selected input or output Line.
LineSource - - - Off,
ExposureActive,
UserOutput0,
UserOutput1,
UserOutput2,
UserOutput3,
Timer1Active,
Timer2Active,
Counter1Active,
Counter2Active,
Counter3Active,
Counter4Active,
AcquisitionActive,
FrameActive,
mvReadOutActive,
LineActive,
mvExposureAndAcquisitionActive,
FrameTriggerWait,
mvExposureActive
 Selects which internal acquisition or I/O source signal to output on the selected Line. LineMode must be Output. Off: Line output is disabled (Tri-State). ExposureActive: Device is doing the exposure of a Frame (or Line). UserOutput0: The chosen User Output Bit state as defined by its current UserOutputValue. UserOutput1: The chosen User Output Bit state as defined by its current UserOutputValue. UserOutput2: The chosen User Output Bit state as defined by its current UserOutputValue. UserOutput3: The chosen User Output Bit state as defined by its current UserOutputValue. Timer1Active: The chosen Timer is in active state. Timer2Active: The chosen Timer is in active state. Counter1Active: The chosen counter is in active state (counting). Counter2Active: The chosen counter is in active state (counting). Counter3Active: The chosen counter is in active state (counting). Counter4Active: The chosen counter is in active state (counting). AcquisitionActive: Device is currently doing an acquisition of one or many Frames. FrameActive: Device is currently doing the capture of a Frame. mvReadOutActive: The sensor is currently read out. LineActive: Device is currently doing the capture of a Line. mvExposureAndAcquisitionActive: The device is currently exposing a frame. FrameTriggerWait: Device is currently waiting for a Frame start trigger. mvExposureActive: The device is currently exposing a frame.
LineFormat - - - mvHighSide
 Controls the current electrical format of the selected physical input or output Line. mvHighSide: The line is currently configured as highside output.
LineInverter - - - 0,
1
 Controls the inversion of the signal of the selected input or output Line.
mvLineDebounceTimeRisingEdge INT64_MIN INT64_MAX 1 - Sets the debounce time in micro seconds for low to high transitions.
mvLineDebounceTimeFallingEdge INT64_MIN INT64_MAX 1 - Sets the debounce time in micro seconds for high to low transitions.
LineStatusAll INT_MIN INT_MAX 0x1 - Returns the current status of all available Line signals at time of polling in a single bitfield.
UserOutputSelector - - - UserOutput0,
UserOutput1,
UserOutput2,
UserOutput3
 Selects which bit of the User Output register will be set by UserOutputValue. UserOutput0: Selects the bit 0 of the User Output register. UserOutput1: Selects the bit 1 of the User Output register. UserOutput2: Selects the bit 2 of the User Output register. UserOutput3: Selects the bit 3 of the User Output register.
UserOutputValue - - - 0,
1
 Sets the value of the bit selected by UserOutputSelector.
UserOutputValueAll INT_MIN INT_MAX 0x1 - Sets the value of all the bits of the User Output register. It is subject to the UserOutputValueAllMask.
UserOutputValueAllMask INT_MIN INT_MAX 0x1 - Sets the write mask to apply to the value specified by UserOutputValueAll before writing it in the User Output register. If the UserOutputValueAllMask feature is present, setting the user Output register using UserOutputValueAll will only change the bits that have a corresponding bit in the mask set to one.
mvEnable12VPowerOut - - - 0,
1
 Enable 12V power out on MultipurposeIO POWER_OUT pin.
Feature Name Min Max Inc Valid Values Documentation
mvDefectivePixelCorrectionControl Contains features to control the device's defective pixel correction parameters.
mvDefectPixelThreshold 0 255 1 - Sets the threshold for the defect pixel detection.
mvDefectPixelSuppressionThreshold 0 255 1 - Sets the threshold for the suppression of false defect pixels.
mvDefectivePixelEnable - - - 0,
1
 Activates the camera's defective pixel correction.
Feature Name Min Max Inc Valid Values Documentation
mvCyclicSignalControl Allows configuration of the cyclic trigger control.
mvCyclicSignalPeriod 1 60000000 1 - Defines the period of the trigger. Equals 1/fps.
mvCyclicSignalDelay 0 1000000 1 - Defines an offset to the modulo trigger.
Feature Name Min Max Inc Valid Values Documentation
ColorTransformationControl A category that contains the Color Transformation control features.
ColorTransformationSelector - - - RGBtoRGB
 Selects which Color Transformation module is controlled by the various Color Transformation features. RGBtoRGB: RGB to RGB color transformation.
ColorTransformationEnable - - - 0,
1
 Activates the selected Color Transformation module.
ColorTransformationValueSelector - - - Gain00,
Gain01,
Gain02,
Gain10,
Gain11,
Gain12,
Gain20,
Gain21,
Gain22,
Offset0,
Offset1,
Offset2
 Selects the Gain factor or Offset of the Transformation matrix to access in the selected Color Transformation module. Gain00: Gain 0,0 of the transformation matrix. Gain01: Gain 0,1 of the transformation matrix. Gain02: Gain 0,2 of the transformation matrix. Gain10: Gain 1,0 of the transformation matrix. Gain11: Gain 1,1 of the transformation matrix. Gain12: Gain 1,2 of the transformation matrix. Gain20: Gain 2,0 of the transformation matrix. Gain21: Gain 2,1 of the transformation matrix. Gain22: Gain 2,2 of the transformation matrix. Offset0: Offset 0 of the transformation matrix. Offset1: Offset 1 of the transformation matrix. Offset2: Offset 2 of the transformation matrix.
ColorTransformationValue -63.984 63.984 - - Represents the value of the selected Gain factor or Offset inside the Transformation matrix.
Feature Name Min Max Inc Valid Values Documentation
ActionControl A category that contains the Action control features.
ActionDeviceKey INT64_MIN INT64_MAX 0x1 - Provides the device key that allows the device to check the validity of action commands. The device internal assertion of an action signal is only authorized if the ActionDeviceKey and the action device key value in the protocol message are equal.
ActionSelector 0 3 1 - Selects to which Action Signal further Action settings apply.
ActionGroupKey 0x0 UINT_MAX 0x1 - Provides the key that the device will use to validate the action on reception of the action protocol message.
ActionGroupMask 0x0 UINT_MAX 0x1 - Provides the mask that the device will use to validate the action on reception of the action protocol message.
Feature Name Min Max Inc Valid Values Documentation
TestControl A category for Test Control features.
TestPendingAck 0 INT_MAX 1 - Tests the device's pending acknowledge feature. When this feature is written, the device waits a time period corresponding to the value of TestPendingAck before acknowledging the write. (ms)
TestEventGenerate@i - - - - Generates a Test Event.
Feature Name Min Max Inc Valid Values Documentation
ChunkDataControl A category that contains the Chunk Data control features.
ChunkModeActive - - - 0,
1
 Activates the inclusion of Chunk data in the transmitted payload.
ChunkSelector - - - Image,
OffsetX,
OffsetY,
Width,
Height,
PixelFormat,
Timestamp,
LineStatusAll,
CounterValue,
TimerValue,
ExposureTime,
SequencerSetActive,
Gain,
mvCustomIdentifier
 Selects which Chunk to enable or control. Image: Image OffsetX: Offset X OffsetY: Offset Y Width: Width Height: Height PixelFormat: Pixel Format Timestamp: Timestamp LineStatusAll: Line Status All CounterValue: Counter Value TimerValue: Timer Value ExposureTime: Exposure Time SequencerSetActive: Sequencer Set Active Gain: Gain mvCustomIdentifier: Selects which Chunk to enable or control.
ChunkEnable - - - 0,
1
 Enables the inclusion of the selected Chunk data in the payload of the image.
Feature Name Min Max Inc Valid Values Documentation
TransportLayerControl Category that contains the Transport layer control features.
PayloadSize INT_MIN INT_MAX 1 - Size of the payload in bytes. This is the total number of bytes sent in the payload. Image data + chunk data if present. No packet headers.
GevVersionMajor 0 65535 1 - This feature is deprecated (See DeviceTLVersionMajor). This is a read only element. It indicates the major version number of the GigE Vision specification supported by this device.
GevVersionMinor 0 65535 1 - This feature is deprecated (See DeviceTLVersionMinor). This is a read only element. It indicates the minor version number of the GigE Vision specification supported by this device.
GevDeviceModeIsBigEndian - - - 0,
1
 This feature is deprecated (See DeviceRegistersEndianness). This is a read only element. It indicates the endianess of the bootstrap registers. True = big endian.
GevDeviceClass - - - Transmitter,
Receiver,
Transceiver,
Peripheral
 This feature is deprecated (See DeviceType). This is a read only element. Its value indicates the device class. Transmitter: This enumeration value indicates that this device acts as a transmitter. Receiver: This enumeration value indicates that this device acts as a receiver. Transceiver: This enumeration value indicates that this device acts as a transceiver. Peripheral: This enumeration value indicates that this device acts as a peripheral device.
GevDeviceModeCharacterSet - - - Reserved,
UTF8,
ASCII
 This feature is deprecated (See DeviceCharacterSet). This is a read only element. Its value indicates the character set used by all the strings in the bootstrap registers. Reserved: This enumeration value indicates that the device uses a reserved representation for all strings in the bootstrap registers. UTF8: This enumeration value indicates that the device uses the UTF-8 representation for all strings in the bootstrap registers. ASCII: This enumeration value indicates that the device uses the ASCII representation for all strings in the bootstrap registers.
GevPhysicalLinkConfiguration - - - SingleLink
 Controls the principal physical link configuration to use on next restart/power-up of the device. SingleLink: This enumeration value indicates that this device shall operate in single-link configuration.
GevCurrentPhysicalLinkConfiguration - - - SingleLink,
MultiLink,
StaticLAG,
DynamicLAG
 This is a read only element. Its value indicates the current physical link configuration of the device. SingleLink: This enumeration value indicates that this device operates in single-link configuration. MultiLink: This enumeration value indicates that this device operates in multi-link configuration. StaticLAG: This enumeration value indicates that this device operates in static LAG configuration. DynamicLAG: This enumeration value indicates that this device operates in dynamic LAG configuration.
GevSupportedOptionSelector - - - SingleLink,
MultiLink,
StaticLAG,
DynamicLAG,
PAUSEFrameReception,
PAUSEFrameGeneration,
IPConfigurationLLA,
IPConfigurationDHCP,
IPConfigurationPersistentIP,
StreamChannelSourceSocket,
StandardIDMode,
MessageChannelSourceSocket,
CommandsConcatenation,
WriteMem,
PacketResend,
Event,
EventData,
PendingAck,
IEEE1588,
IEEE1588ExtendedCapabilities,
Action,
UnconditionalAction,
ScheduledAction,
PrimaryApplicationSwitchover,
ExtendedStatusCodes,
ExtendedStatusCodesVersion2_0,
DiscoveryAckDelay,
DiscoveryAckDelayWritable,
TestData,
ManifestTable,
CCPApplicationSocket,
LinkSpeed,
HeartbeatDisable,
SerialNumber,
UserDefinedName,
StreamChannel0ExtendedChunkData,
StreamChannel0UnconditionalStreaming,
StreamChannel0AllInTransmission,
StreamChannel0ResendDestination,
StreamChannel0MultiZone,
StreamChannel0LargeLeaderTrailer,
StreamChannel0MultiPart,
StreamChannel0IPReassembly,
StreamChannel0BigAndLittleEndian
 This enumeration lists the available GEV options to interrogate for existing support. SingleLink: Selects the GEV option to interrogate for existing support. MultiLink: Selects the GEV option to interrogate for existing support. StaticLAG: Selects the GEV option to interrogate for existing support. DynamicLAG: Selects the GEV option to interrogate for existing support. PAUSEFrameReception: Selects the GEV option to interrogate for existing support. PAUSEFrameGeneration: Selects the GEV option to interrogate for existing support. IPConfigurationLLA: Selects the GEV option to interrogate for existing support. IPConfigurationDHCP: Selects the GEV option to interrogate for existing support. IPConfigurationPersistentIP: Selects the GEV option to interrogate for existing support. StreamChannelSourceSocket: Selects the GEV option to interrogate for existing support. StandardIDMode: Selects the GEV option to interrogate for existing support. MessageChannelSourceSocket: Selects the GEV option to interrogate for existing support. CommandsConcatenation: Selects the GEV option to interrogate for existing support. WriteMem: Selects the GEV option to interrogate for existing support. PacketResend: Selects the GEV option to interrogate for existing support. Event: Selects the GEV option to interrogate for existing support. EventData: Selects the GEV option to interrogate for existing support. PendingAck: Selects the GEV option to interrogate for existing support. IEEE1588: Selects the GEV option to interrogate for existing support. IEEE1588ExtendedCapabilities: Selects the GEV option to interrogate for existing support. Action: Selects the GEV option to interrogate for existing support. UnconditionalAction: Selects the GEV option to interrogate for existing support. ScheduledAction: Selects the GEV option to interrogate for existing support. PrimaryApplicationSwitchover: Selects the GEV option to interrogate for existing support. ExtendedStatusCodes: Selects the GEV option to interrogate for existing support. ExtendedStatusCodesVersion2_0: Selects the GEV option to interrogate for existing support. DiscoveryAckDelay: Selects the GEV option to interrogate for existing support. DiscoveryAckDelayWritable: Selects the GEV option to interrogate for existing support. TestData: Selects the GEV option to interrogate for existing support. ManifestTable: Selects the GEV option to interrogate for existing support. CCPApplicationSocket: Selects the GEV option to interrogate for existing support. LinkSpeed: Selects the GEV option to interrogate for existing support. HeartbeatDisable: Selects the GEV option to interrogate for existing support. SerialNumber: Selects the GEV option to interrogate for existing support. UserDefinedName: Selects the GEV option to interrogate for existing support. StreamChannel0ExtendedChunkData: Selects the GEV option to interrogate for existing support. StreamChannel0UnconditionalStreaming: Selects the GEV option to interrogate for existing support. StreamChannel0AllInTransmission: Selects the GEV option to interrogate for existing support. StreamChannel0ResendDestination: Selects the GEV option to interrogate for existing support. StreamChannel0MultiZone: Selects the GEV option to interrogate for existing support. StreamChannel0LargeLeaderTrailer: Selects the GEV option to interrogate for existing support. StreamChannel0MultiPart: Selects the GEV option to interrogate for existing support. StreamChannel0IPReassembly: Selects the GEV option to interrogate for existing support. StreamChannel0BigAndLittleEndian: Selects the GEV option to interrogate for existing support.
GevSupportedOption - - - 0,
1
 This is a read only element. It indicates whether the selected option is supported or not.
GevInterfaceSelector 0 0 1 - This selects the physical network interface to configure. Once a network interface has been selected, all changes to the network interface settings will be applied to the selected interface.
GevLinkSpeed 0 UINT_MAX 1 - This feature is deprecated (See DeviceLinkSpeed). This is a read only element. It indicates the connection speed in Mbps for the selected network interface.
GevMACAddress INT64_MIN INT64_MAX 0x000000000001 - This is a read only element. It indicates the MAC address for the selected network interface.
GevPAUSEFrameReception - - - 0,
1
 Controls whether incoming PAUSE Frames are handled on the given logical link.
GevPAUSEFrameTransmission - - - 0,
1
 Controls whether PAUSE Frames can be generated on the given logical link.
GevCurrentIPConfigurationLLA - - - 0,
1
 This is a read only element. It indicates whether the selected network interface has auto IP addressing (also known as LLA) activated.
GevCurrentIPConfigurationDHCP - - - 0,
1
 This element indicates whether the selected network interface has DHCP IP addressing activated.
GevCurrentIPConfigurationPersistentIP - - - 0,
1
 This element indicates whether the selected network interface supports fixed IP addressing (also known as persistent IP addressing).
GevCurrentIPAddress 0x00000000 UINT_MAX 0x00000001 - This is a read only element. It indicates the current IP address for the selected network interface.
GevCurrentSubnetMask 0x00000000 UINT_MAX 0x00000001 - This is a read only element. It indicates the current subnet mask for the selected network interface.
GevCurrentDefaultGateway 0x00000000 UINT_MAX 0x00000001 - This is a read only element. It indicates the current default gateway for the selected network interface.
GevFirstURL - - - - This is a read only element. It indicates the first URL to the XML device description file.
GevSecondURL - - - - This is a read only element. It indicates the second URL to the XML device description file.
GevNumberOfInterfaces 0 UINT_MAX 1 - This feature is deprecated (See DeviceLinkSelector). This is a read only element. It indicates the number of network interfaces on the device.
GevPersistentIPAddress 0x00000000 UINT_MAX 0x00000001 - This value sets the fixed IP address for the selected network interface (if fixed IP addressing is supported by the device and enabled).
GevPersistentSubnetMask 0x00000000 UINT_MAX 0x00000001 - This value sets the fixed subnet mask for the selected network interface (if fixed IP addressing is supported by the device and enabled).
GevPersistentDefaultGateway 0x00000000 UINT_MAX 0x00000001 - This value sets the fixed default gateway for the selected network interface (if fixed IP addressing is supported by the device and enabled).
GevMessageChannelCount 0 UINT_MAX 1 - This feature is deprecated (See DeviceEventChannelCount). This is a read only element. It indicates the number of message channels supported by the device.
GevStreamChannelCount 0 UINT_MAX 1 - This feature is deprecated (See DeviceStreamChannelCount). This is a read only element. It indicates the number of stream channels supported by the device.
GevHeartbeatTimeout 0 UINT_MAX 1 - This feature is deprecated (See DeviceLinkHeartbeatTimeout). This value sets the heartbeat timeout in milliseconds.
GevTimestampTickFrequency 0 UINT_MAX 1 - This is a read only element. It indicates the number of timestamp clock ticks in 1 second.
GevTimestampControlLatch@i - - - - This feature is deprecated (See TimestampLatch). This command latches the current timestamp value of the device.
GevTimestampControlReset@i - - - - This feature is deprecated (See TimestampReset). This command resets the timestamp value for the device
GevTimestampControlLatchReset@i - - - - This feature is deprecated (See TimestampLatch and TimestampReset). This command resets the timestamp control latch.
GevTimestampValue INT64_MIN INT64_MAX 1 - This feature is deprecated (See TimestampLatchValue). This is a read only element. It indicates the latched value of the timestamp(The timestamp must first be latched using the GevTimestampControlLatch command)
GevDiscoveryAckDelay 0 1000 1 - Indicates the maximum randomized delay(in ms) the device will wait to acknowledge a discovery command.
GevGVCPExtendedStatusCodesSelector - - - Version1_1
 Selects the GigE Vision version to control extended status codes for. Version1_1: This enumeration value indicates that extended status code for GEV 1.1 shall be configured.
GevGVCPExtendedStatusCodes - - - 0,
1
 This feature is used to enable the generation of extended status codes.
GevGVCPPendingAck - - - 0,
1
 This feature is used to enable the generation of PENDING_ACK commands.
GevGVCPHeartbeatDisable - - - 0,
1
 This feature is deprecated (See DeviceHeartbeatMode). It was used to disable the GVCP heartbeat.
GevGVCPPendingTimeout 0 65535 1 - This feature is deprecated (See DeviceLinkCommandTimeout). It was used to indicate the longest GVCP command execution time before a device returns a PENDING_ACK.
GevPrimaryApplicationSwitchoverKey INT64_MIN INT64_MAX 1 - Controls the key to use to authenticate primary application switchover requests.
GevGVSPExtendedIDMode - - - Off,
On
 This enumeration enables the extended IDs mode. Off: This enumeration value disables the extended IDs mode. On: This enumeration value enables the extended IDs mode.
GevPrimaryApplicationSocket 0 65535 1 - This value indicates the UDP source port of the primary application.
GevPrimaryApplicationIPAddress 0x00000000 UINT_MAX 0x00000001 - This value indicates the primary applications IPv4 address.
GevMCPHostPort 0 65535 1 - This value indicates the port to which the device must send messages. Setting this value to 0 closes the message channel.
GevMCDA 0x00000000 UINT_MAX 0x00000001 - This value sets the message channel destination IPv4 address. The destination can be a unicast or a multicast.
GevMCTT 0 UINT_MAX 1 - This feature provides the transmission timeout value in milliseconds.
GevMCRC 0 UINT_MAX 1 - This feature indicates the number of retransmissions allowed when a message channel message times out.
GevMCSP 0 65535 1 - This value indicates the source port of the message channel.
GevStreamChannelSelector 0 0 1 - This enumeration selects the stream channels to configure. Once a stream channel has been selected, all changes to the stream channel settings will be applied to the selected stream channel.
GevSCCFGExtendedChunkData - - - 0,
1
 Enables devices to use the extended chunk data payload type for this stream channel.
GevSCPDirection - - - Transmitter,
Receiver
 This feature is deprecated (See DeviceStreamChannelType). This is a read only element. Its value reports the direction of the stream channel. Transmitter: This enumeration value indicates that this device acts as a transmitter. Receiver: This enumeration value indicates that this device acts as a receiver.
GevSCPInterfaceIndex 0 0 1 - This value sets the index of the network interface to use.
GevSCPHostPort 0 65535 1 - This value sets the port to which the device must send data streams.
GevSCPSFireTestPacket - - - 0,
1
 When this bit is set, the device will fire one test packet of size specified by bit 16-31. The 'do not fragment' bit of IP header must be set for this test packet.
GevSCPSDoNotFragment - - - 0,
1
 This bit is copied into the 'do not fragment' bit of IP header of each stream packet. It can be used by the application to prevent IP fragmentation of packets on the stream channel.
GevSCPSBigEndian - - - 0,
1
 This feature is deprecated (See DeviceStreamChannelEndianness). Endianess of multi-byte pixel data for this stream.
GevSCPSPacketSize 400 9000 8 - This value sets the packet size in bytes for the selected stream channel. Excludes data leader and data trailer. (The last packet may be smaller because the packet size is not necessarily a multiple of the block size for the stream channel.)
GevSCPD 0 1000 1 - This value sets a delay between the transmission of each packet for the selected stream channel. The delay is measured in ticks.
GevSCDA 0x00000000 UINT_MAX 0x00000001 - This value sets the stream channel destination IPv4 address for the selected stream channel. The destination can be a unicast or a multicast.
GevSCSP 0 UINT_MAX 1 - This value indicates the source port of the stream channel.
mvGevSCBWControl - - - GevSCPD,
mvGevSCBW
 This feature is deprecated (See DeviceLinkThroughputLimitMode). This enumeration selects the bandwidth control for the selected stream channel. GevSCPD: This feature is deprecated (See DeviceLinkThroughputLimitMode). Selects the bandwidth control for the selected stream channel. mvGevSCBW: This feature is deprecated (See DeviceLinkThroughputLimitMode). Selects the bandwidth control for the selected stream channel.
mvGevSCBW INT64_MIN INT64_MAX 1 - This feature is deprecated (See DeviceLinkThroughputLimit). This value sets the stream channels max. bandwidth in KBps.
Feature Name Min Max Inc Valid Values Documentation
PtpControl Category that contains the features related to the Precision Time Protocol (PTP) of the device.
PtpEnable - - - 0,
1
 Enables the Precision Time Protocol (PTP).
PtpDataSetLatch@i - - - - Latches the current values from the device's PTP clock data set.
PtpStatus - - - Undefined,
Initializing,
Faulty,
Disabled,
Listening,
PreMaster,
Master,
Passive,
Uncalibrated,
Slave
 This is a read only element. The state is indicated by values 1 to 9, corresponding to the states INITIALIZING, FAULTY, DISABLED, LISTENING, PRE_MASTER, MASTER, PASSIVE, UNCALIBRATED, and SLAVE. Refer to the IEEE 1588-2008 specification for additional information. Undefined: This enumeration value indicates that the IEEE1588 status is 'Undefined'. Initializing: This enumeration value indicates that the IEEE1588 status is 'Initializing'. Faulty: This enumeration value indicates that the IEEE1588 status is 'Faulty'. Disabled: This enumeration value indicates that the IEEE1588 status is 'Disabled'. Listening: This enumeration value indicates that the IEEE1588 status is 'Listening'. PreMaster: This enumeration value indicates that the IEEE1588 status is 'PreMaster'. Master: This enumeration value indicates that the IEEE1588 status is 'Master'. Passive: This enumeration value indicates that the IEEE1588 status is 'Passive'. Uncalibrated: This enumeration value indicates that the IEEE1588 status is 'Uncalibrated'. Slave: This enumeration value indicates that the IEEE1588 status is 'Slave'.
Feature Name Min Max Inc Valid Values Documentation
UserSetControl A category that contains the User Set control features.
UserSetSelector - - - Default,
UserSet1,
UserSet2,
UserSet3,
UserSet4
 Selects the feature User Set to load, save or configure. Default: Selects the factory setting user set. UserSet1: Selects the user set 1. UserSet2: Selects the user set 2. UserSet3: Selects the user set 3. UserSet4: Selects the user set 4.
UserSetLoad@i - - - - Loads the User Set specified by UserSetSelector to the device and makes it active.
UserSetSave@i - - - - Save the User Set specified by UserSetSelector to the non-volatile memory of the device.
UserSetDefault - - - Default,
UserSet1,
UserSet2,
UserSet3,
UserSet4
 Selects the feature User Set to load and make active by default when the device is reset. Default: Select the factory setting user set. UserSet1: Select the user set 1. UserSet2: Select the user set 2. UserSet3: Select the user set 3. UserSet4: Select the user set 4.
UserSetDefaultSelector - - - Default,
UserSet1,
UserSet2,
UserSet3,
UserSet4
 This feature is deprecated (See UserSetDefault). Selects the feature User Set to load and make active when the device is reset. Default: Select the factory setting user set. UserSet1: Select the user set 1. UserSet2: Select the user set 2. UserSet3: Select the user set 3. UserSet4: Select the user set 4.
Feature Name Min Max Inc Valid Values Documentation
EventControl A category that contains Event control features.
EventSelector - - - ExposureEnd,
Line4RisingEdge,
Line4FallingEdge,
Line4AnyEdge,
Line5RisingEdge,
Line5FallingEdge,
Line5AnyEdge,
Line6RisingEdge,
Line6FallingEdge,
Line6AnyEdge,
Line7RisingEdge,
Line7FallingEdge,
Line7AnyEdge,
FrameEnd,
DeviceTemperatureStateNormal,
DeviceTemperatureStateCritical,
DeviceTemperatureStateOverTemperature
 Selects which Event to signal to the host application. ExposureEnd: Device just completed the exposure of one Frame (or Line). Line4RisingEdge: The event will be generated when a Rising Edge is detected on the Line 4. Line4FallingEdge: The event will be generated when a Falling Edge is detected on the Line 4. Line4AnyEdge: The event will be generated when a Falling or Rising Edge is detected on the Line 4. Line5RisingEdge: The event will be generated when a Rising Edge is detected on the Line 5. Line5FallingEdge: The event will be generated when a Falling Edge is detected on the Line 5. Line5AnyEdge: The event will be generated when a Falling or Rising Edge is detected on the Line 5. Line6RisingEdge: The event will be generated when a Rising Edge is detected on the Line 6. Line6FallingEdge: The event will be generated when a Falling Edge is detected on the Line 6. Line6AnyEdge: The event will be generated when a Falling or Rising Edge is detected on the Line 6. Line7RisingEdge: The event will be generated when a Rising Edge is detected on the Line 7. Line7FallingEdge: The event will be generated when a Falling Edge is detected on the Line 7. Line7AnyEdge: The event will be generated when a Falling or Rising Edge is detected on the Line 7. FrameEnd: Device just completed the capture of one Frame. DeviceTemperatureStateNormal: Selects which Event to signal to the host application. DeviceTemperatureStateCritical: Selects which Event to signal to the host application. DeviceTemperatureStateOverTemperature: Selects which Event to signal to the host application.
EventNotification - - - Off,
On
 Activate or deactivate the notification to the host application of the occurrence of the selected Event. Off: The selected Event notification is disabled. On: The selected Event notification is enabled.
Feature Name Min Max Inc Valid Values Documentation
EventExposureEndData A category that contains all the data features related to the EventExposureEnd event.
EventExposureEnd INT64_MIN INT64_MAX 0x1 - This feature returns the unique identifier of the 'EventExposureEnd' event.
EventExposureEndStreamChannelIndex INT64_MIN INT64_MAX 1 - Returns the index of the stream channel that generated the 'EventExposureEnd' event.
EventExposureEndFrameID INT64_MIN INT64_MAX 1 - Returns the unique Identifier of the frame (or image) that generated the 'Event Exposure End Frame ID' event.
EventExposureEndTimestamp INT64_MIN INT64_MAX 1 - Returns the timestamp of the 'Event Exposure End Timestamp' event. It can be used to determine when the event occurred.
Feature Name Min Max Inc Valid Values Documentation
EventLine4RisingEdgeData A category that contains all the data features related to the EventLine4RisingEdge event.
EventLine4RisingEdge INT64_MIN INT64_MAX 0x1 - This feature returns the unique identifier of the 'EventLine4RisingEdge' event.
EventLine4RisingEdgeStreamChannelIndex INT64_MIN INT64_MAX 1 - Returns the index of the stream channel that generated the 'EventLine4RisingEdge' event.
EventLine4RisingEdgeFrameID INT64_MIN INT64_MAX 1 - Returns the unique Identifier of the frame (or image) that generated the 'Event Line 4 Rising Edge Frame ID' event.
EventLine4RisingEdgeTimestamp INT64_MIN INT64_MAX 1 - Returns the timestamp of the 'Event Line 4 Rising Edge Timestamp' event. It can be used to determine when the event occurred.
Feature Name Min Max Inc Valid Values Documentation
EventLine4FallingEdgeData A category that contains all the data features related to the EventLine4FallingEdge event.
EventLine4FallingEdge INT64_MIN INT64_MAX 0x1 - This feature returns the unique identifier of the 'EventLine4FallingEdge' event.
EventLine4FallingEdgeStreamChannelIndex INT64_MIN INT64_MAX 1 - Returns the index of the stream channel that generated the 'EventLine4FallingEdge' event.
EventLine4FallingEdgeFrameID INT64_MIN INT64_MAX 1 - Returns the unique Identifier of the frame (or image) that generated the 'Event Line 4 Falling Edge Frame ID' event.
EventLine4FallingEdgeTimestamp INT64_MIN INT64_MAX 1 - Returns the timestamp of the 'Event Line 4 Falling Edge Timestamp' event. It can be used to determine when the event occurred.
Feature Name Min Max Inc Valid Values Documentation
EventLine4AnyEdgeData A category that contains all the data features related to the EventLine4AnyEdge event.
EventLine4AnyEdge INT64_MIN INT64_MAX 0x1 - This feature returns the unique identifier of the 'EventLine4AnyEdge' event.
EventLine4AnyEdgeStreamChannelIndex INT64_MIN INT64_MAX 1 - Returns the index of the stream channel that generated the 'EventLine4AnyEdge' event.
EventLine4AnyEdgeFrameID INT64_MIN INT64_MAX 1 - Returns the unique Identifier of the frame (or image) that generated the 'Event Line 4 Any Edge Frame ID' event.
EventLine4AnyEdgeTimestamp INT64_MIN INT64_MAX 1 - Returns the timestamp of the 'Event Line 4 Any Edge Timestamp' event. It can be used to determine when the event occurred.
Feature Name Min Max Inc Valid Values Documentation
EventLine5RisingEdgeData A category that contains all the data features related to the EventLine5RisingEdge event.
EventLine5RisingEdge INT64_MIN INT64_MAX 0x1 - This feature returns the unique identifier of the 'EventLine5RisingEdge' event.
EventLine5RisingEdgeStreamChannelIndex INT64_MIN INT64_MAX 1 - Returns the index of the stream channel that generated the 'EventLine5RisingEdge' event.
EventLine5RisingEdgeFrameID INT64_MIN INT64_MAX 1 - Returns the unique Identifier of the frame (or image) that generated the 'Event Line 5 Rising Edge Frame ID' event.
EventLine5RisingEdgeTimestamp INT64_MIN INT64_MAX 1 - Returns the timestamp of the 'Event Line 5 Rising Edge Timestamp' event. It can be used to determine when the event occurred.
Feature Name Min Max Inc Valid Values Documentation
EventLine5FallingEdgeData A category that contains all the data features related to the EventLine5FallingEdge event.
EventLine5FallingEdge INT64_MIN INT64_MAX 0x1 - This feature returns the unique identifier of the 'EventLine5FallingEdge' event.
EventLine5FallingEdgeStreamChannelIndex INT64_MIN INT64_MAX 1 - Returns the index of the stream channel that generated the 'EventLine5FallingEdge' event.
EventLine5FallingEdgeFrameID INT64_MIN INT64_MAX 1 - Returns the unique Identifier of the frame (or image) that generated the 'Event Line 5 Falling Edge Frame ID' event.
EventLine5FallingEdgeTimestamp INT64_MIN INT64_MAX 1 - Returns the timestamp of the 'Event Line 5 Falling Edge Timestamp' event. It can be used to determine when the event occurred.
Feature Name Min Max Inc Valid Values Documentation
EventLine5AnyEdgeData A category that contains all the data features related to the EventLine5AnyEdge event.
EventLine5AnyEdge INT64_MIN INT64_MAX 0x1 - This feature returns the unique identifier of the 'EventLine5AnyEdge' event.
EventLine5AnyEdgeStreamChannelIndex INT64_MIN INT64_MAX 1 - Returns the index of the stream channel that generated the 'EventLine5AnyEdge' event.
EventLine5AnyEdgeFrameID INT64_MIN INT64_MAX 1 - Returns the unique Identifier of the frame (or image) that generated the 'Event Line 5 Any Edge Frame ID' event.
EventLine5AnyEdgeTimestamp INT64_MIN INT64_MAX 1 - Returns the timestamp of the 'Event Line 5 Any Edge Timestamp' event. It can be used to determine when the event occurred.
Feature Name Min Max Inc Valid Values Documentation
EventLine6RisingEdgeData A category that contains all the data features related to the EventLine6RisingEdge event.
EventLine6RisingEdge INT64_MIN INT64_MAX 0x1 - This feature returns the unique identifier of the 'EventLine6RisingEdge' event.
EventLine6RisingEdgeStreamChannelIndex INT64_MIN INT64_MAX 1 - Returns the index of the stream channel that generated the 'EventLine6RisingEdge' event.
EventLine6RisingEdgeFrameID INT64_MIN INT64_MAX 1 - Returns the unique Identifier of the frame (or image) that generated the 'Event Line 6 Rising Edge Frame ID' event.
EventLine6RisingEdgeTimestamp INT64_MIN INT64_MAX 1 - Returns the timestamp of the 'Event Line 6 Rising Edge Timestamp' event. It can be used to determine when the event occurred.
Feature Name Min Max Inc Valid Values Documentation
EventLine6FallingEdgeData A category that contains all the data features related to the EventLine6FallingEdge event.
EventLine6FallingEdge INT64_MIN INT64_MAX 0x1 - This feature returns the unique identifier of the 'EventLine6FallingEdge' event.
EventLine6FallingEdgeStreamChannelIndex INT64_MIN INT64_MAX 1 - Returns the index of the stream channel that generated the 'EventLine6FallingEdge' event.
EventLine6FallingEdgeFrameID INT64_MIN INT64_MAX 1 - Returns the unique Identifier of the frame (or image) that generated the 'Event Line 6 Falling Edge Frame ID' event.
EventLine6FallingEdgeTimestamp INT64_MIN INT64_MAX 1 - Returns the timestamp of the 'Event Line 6 Falling Edge Timestamp' event. It can be used to determine when the event occurred.
Feature Name Min Max Inc Valid Values Documentation
EventLine6AnyEdgeData A category that contains all the data features related to the EventLine6AnyEdge event.
EventLine6AnyEdge INT64_MIN INT64_MAX 0x1 - This feature returns the unique identifier of the 'EventLine6AnyEdge' event.
EventLine6AnyEdgeStreamChannelIndex INT64_MIN INT64_MAX 1 - Returns the index of the stream channel that generated the 'EventLine6AnyEdge' event.
EventLine6AnyEdgeFrameID INT64_MIN INT64_MAX 1 - Returns the unique Identifier of the frame (or image) that generated the 'Event Line 6 Any Edge Frame ID' event.
EventLine6AnyEdgeTimestamp INT64_MIN INT64_MAX 1 - Returns the timestamp of the 'Event Line 6 Any Edge Timestamp' event. It can be used to determine when the event occurred.
Feature Name Min Max Inc Valid Values Documentation
EventLine7RisingEdgeData A category that contains all the data features related to the EventLine7RisingEdge event.
EventLine7RisingEdge INT64_MIN INT64_MAX 0x1 - This feature returns the unique identifier of the 'EventLine7RisingEdge' event.
EventLine7RisingEdgeStreamChannelIndex INT64_MIN INT64_MAX 1 - Returns the index of the stream channel that generated the 'EventLine7RisingEdge' event.
EventLine7RisingEdgeFrameID INT64_MIN INT64_MAX 1 - Returns the unique Identifier of the frame (or image) that generated the 'Event Line 7 Rising Edge Frame ID' event.
EventLine7RisingEdgeTimestamp INT64_MIN INT64_MAX 1 - Returns the timestamp of the 'Event Line 7 Rising Edge Timestamp' event. It can be used to determine when the event occurred.
Feature Name Min Max Inc Valid Values Documentation
EventLine7FallingEdgeData A category that contains all the data features related to the EventLine7FallingEdge event.
EventLine7FallingEdge INT64_MIN INT64_MAX 0x1 - This feature returns the unique identifier of the 'EventLine7FallingEdge' event.
EventLine7FallingEdgeStreamChannelIndex INT64_MIN INT64_MAX 1 - Returns the index of the stream channel that generated the 'EventLine7FallingEdge' event.
EventLine7FallingEdgeFrameID INT64_MIN INT64_MAX 1 - Returns the unique Identifier of the frame (or image) that generated the 'Event Line 7 Falling Edge Frame ID' event.
EventLine7FallingEdgeTimestamp INT64_MIN INT64_MAX 1 - Returns the timestamp of the 'Event Line 7 Falling Edge Timestamp' event. It can be used to determine when the event occurred.
Feature Name Min Max Inc Valid Values Documentation
EventLine7AnyEdgeData A category that contains all the data features related to the EventLine7AnyEdge event.
EventLine7AnyEdge INT64_MIN INT64_MAX 0x1 - This feature returns the unique identifier of the 'EventLine7AnyEdge' event.
EventLine7AnyEdgeStreamChannelIndex INT64_MIN INT64_MAX 1 - Returns the index of the stream channel that generated the 'EventLine7AnyEdge' event.
EventLine7AnyEdgeFrameID INT64_MIN INT64_MAX 1 - Returns the unique Identifier of the frame (or image) that generated the 'Event Line 7 Any Edge Frame ID' event.
EventLine7AnyEdgeTimestamp INT64_MIN INT64_MAX 1 - Returns the timestamp of the 'Event Line 7 Any Edge Timestamp' event. It can be used to determine when the event occurred.
Feature Name Min Max Inc Valid Values Documentation
EventLine8RisingEdgeData A category that contains all the data features related to the EventLine8RisingEdge event.
EventLine8RisingEdge INT64_MIN INT64_MAX 0x1 - This feature returns the unique identifier of the 'EventLine8RisingEdge' event.
EventLine8RisingEdgeStreamChannelIndex INT64_MIN INT64_MAX 1 - Returns the index of the stream channel that generated the 'EventLine8RisingEdge' event.
EventLine8RisingEdgeFrameID INT64_MIN INT64_MAX 1 - Returns the unique Identifier of the frame (or image) that generated the 'Event Line 8 Rising Edge Frame ID' event.
EventLine8RisingEdgeTimestamp INT64_MIN INT64_MAX 1 - Returns the timestamp of the 'Event Line 8 Rising Edge Timestamp' event. It can be used to determine when the event occurred.
Feature Name Min Max Inc Valid Values Documentation
EventLine8FallingEdgeData A category that contains all the data features related to the EventLine8FallingEdge event.
EventLine8FallingEdge INT64_MIN INT64_MAX 0x1 - This feature returns the unique identifier of the 'EventLine8FallingEdge' event.
EventLine8FallingEdgeStreamChannelIndex INT64_MIN INT64_MAX 1 - Returns the index of the stream channel that generated the 'EventLine8FallingEdge' event.
EventLine8FallingEdgeFrameID INT64_MIN INT64_MAX 1 - Returns the unique Identifier of the frame (or image) that generated the 'Event Line 8 Falling Edge Frame ID' event.
EventLine8FallingEdgeTimestamp INT64_MIN INT64_MAX 1 - Returns the timestamp of the 'Event Line 8 Falling Edge Timestamp' event. It can be used to determine when the event occurred.
Feature Name Min Max Inc Valid Values Documentation
EventLine8AnyEdgeData A category that contains all the data features related to the EventLine8AnyEdge event.
EventLine8AnyEdge INT64_MIN INT64_MAX 0x1 - This feature returns the unique identifier of the 'EventLine8AnyEdge' event.
EventLine8AnyEdgeStreamChannelIndex INT64_MIN INT64_MAX 1 - Returns the index of the stream channel that generated the 'EventLine8AnyEdge' event.
EventLine8AnyEdgeFrameID INT64_MIN INT64_MAX 1 - Returns the unique Identifier of the frame (or image) that generated the 'Event Line 8 Any Edge Frame ID' event.
EventLine8AnyEdgeTimestamp INT64_MIN INT64_MAX 1 - Returns the timestamp of the 'Event Line 8 Any Edge Timestamp' event. It can be used to determine when the event occurred.
Feature Name Min Max Inc Valid Values Documentation
EventLine9RisingEdgeData A category that contains all the data features related to the EventLine9RisingEdge event.
EventLine9RisingEdge INT64_MIN INT64_MAX 0x1 - This feature returns the unique identifier of the 'EventLine9RisingEdge' event.
EventLine9RisingEdgeStreamChannelIndex INT64_MIN INT64_MAX 1 - Returns the index of the stream channel that generated the 'EventLine9RisingEdge' event.
EventLine9RisingEdgeFrameID INT64_MIN INT64_MAX 1 - Returns the unique Identifier of the frame (or image) that generated the 'Event Line 9 Rising Edge Frame ID' event.
EventLine9RisingEdgeTimestamp INT64_MIN INT64_MAX 1 - Returns the timestamp of the 'Event Line 9 Rising Edge Timestamp' event. It can be used to determine when the event occurred.
Feature Name Min Max Inc Valid Values Documentation
EventLine9FallingEdgeData A category that contains all the data features related to the EventLine9FallingEdge event.
EventLine9FallingEdge INT64_MIN INT64_MAX 0x1 - This feature returns the unique identifier of the 'EventLine9FallingEdge' event.
EventLine9FallingEdgeStreamChannelIndex INT64_MIN INT64_MAX 1 - Returns the index of the stream channel that generated the 'EventLine9FallingEdge' event.
EventLine9FallingEdgeFrameID INT64_MIN INT64_MAX 1 - Returns the unique Identifier of the frame (or image) that generated the 'Event Line 9 Falling Edge Frame ID' event.
EventLine9FallingEdgeTimestamp INT64_MIN INT64_MAX 1 - Returns the timestamp of the 'Event Line 9 Falling Edge Timestamp' event. It can be used to determine when the event occurred.
Feature Name Min Max Inc Valid Values Documentation
EventLine9AnyEdgeData A category that contains all the data features related to the EventLine9AnyEdge event.
EventLine9AnyEdge INT64_MIN INT64_MAX 0x1 - This feature returns the unique identifier of the 'EventLine9AnyEdge' event.
EventLine9AnyEdgeStreamChannelIndex INT64_MIN INT64_MAX 1 - Returns the index of the stream channel that generated the 'EventLine9AnyEdge' event.
EventLine9AnyEdgeFrameID INT64_MIN INT64_MAX 1 - Returns the unique Identifier of the frame (or image) that generated the 'Event Line 9 Any Edge Frame ID' event.
EventLine9AnyEdgeTimestamp INT64_MIN INT64_MAX 1 - Returns the timestamp of the 'Event Line 9 Any Edge Timestamp' event. It can be used to determine when the event occurred.
Feature Name Min Max Inc Valid Values Documentation
EventLine10RisingEdgeData A category that contains all the data features related to the EventLine10RisingEdge event.
EventLine10RisingEdge INT64_MIN INT64_MAX 0x1 - This feature returns the unique identifier of the 'EventLine10RisingEdge' event.
EventLine10RisingEdgeStreamChannelIndex INT64_MIN INT64_MAX 1 - Returns the index of the stream channel that generated the 'EventLine10RisingEdge' event.
EventLine10RisingEdgeFrameID INT64_MIN INT64_MAX 1 - Returns the unique Identifier of the frame (or image) that generated the 'Event Line 10 Rising Edge Frame ID' event.
EventLine10RisingEdgeTimestamp INT64_MIN INT64_MAX 1 - Returns the timestamp of the 'Event Line 10 Rising Edge Timestamp' event. It can be used to determine when the event occurred.
Feature Name Min Max Inc Valid Values Documentation
EventLine10FallingEdgeData A category that contains all the data features related to the EventLine10FallingEdge event.
EventLine10FallingEdge INT64_MIN INT64_MAX 0x1 - This feature returns the unique identifier of the 'EventLine10FallingEdge' event.
EventLine10FallingEdgeStreamChannelIndex INT64_MIN INT64_MAX 1 - Returns the index of the stream channel that generated the 'EventLine10FallingEdge' event.
EventLine10FallingEdgeFrameID INT64_MIN INT64_MAX 1 - Returns the unique Identifier of the frame (or image) that generated the 'Event Line 10 Falling Edge Frame ID' event.
EventLine10FallingEdgeTimestamp INT64_MIN INT64_MAX 1 - Returns the timestamp of the 'Event Line 10 Falling Edge Timestamp' event. It can be used to determine when the event occurred.
Feature Name Min Max Inc Valid Values Documentation
EventLine10AnyEdgeData A category that contains all the data features related to the EventLine10AnyEdge event.
EventLine10AnyEdge INT64_MIN INT64_MAX 0x1 - This feature returns the unique identifier of the 'EventLine10AnyEdge' event.
EventLine10AnyEdgeStreamChannelIndex INT64_MIN INT64_MAX 1 - Returns the index of the stream channel that generated the 'EventLine10AnyEdge' event.
EventLine10AnyEdgeFrameID INT64_MIN INT64_MAX 1 - Returns the unique Identifier of the frame (or image) that generated the 'Event Line 10 Any Edge Frame ID' event.
EventLine10AnyEdgeTimestamp INT64_MIN INT64_MAX 1 - Returns the timestamp of the 'Event Line 10 Any Edge Timestamp' event. It can be used to determine when the event occurred.
Feature Name Min Max Inc Valid Values Documentation
EventLine11RisingEdgeData A category that contains all the data features related to the EventLine11RisingEdge event.
EventLine11RisingEdge INT64_MIN INT64_MAX 0x1 - This feature returns the unique identifier of the 'EventLine11RisingEdge' event.
EventLine11RisingEdgeStreamChannelIndex INT64_MIN INT64_MAX 1 - Returns the index of the stream channel that generated the 'EventLine11RisingEdge' event.
EventLine11RisingEdgeFrameID INT64_MIN INT64_MAX 1 - Returns the unique Identifier of the frame (or image) that generated the 'Event Line 11 Rising Edge Frame ID' event.
EventLine11RisingEdgeTimestamp INT64_MIN INT64_MAX 1 - Returns the timestamp of the 'Event Line 11 Rising Edge Timestamp' event. It can be used to determine when the event occurred.
Feature Name Min Max Inc Valid Values Documentation
EventLine11FallingEdgeData A category that contains all the data features related to the EventLine11FallingEdge event.
EventLine11FallingEdge INT64_MIN INT64_MAX 0x1 - This feature returns the unique identifier of the 'EventLine11FallingEdge' event.
EventLine11FallingEdgeStreamChannelIndex INT64_MIN INT64_MAX 1 - Returns the index of the stream channel that generated the 'EventLine11FallingEdge' event.
EventLine11FallingEdgeFrameID INT64_MIN INT64_MAX 1 - Returns the unique Identifier of the frame (or image) that generated the 'Event Line 11 Falling Edge Frame ID' event.
EventLine11FallingEdgeTimestamp INT64_MIN INT64_MAX 1 - Returns the timestamp of the 'Event Line 11 Falling Edge Timestamp' event. It can be used to determine when the event occurred.
Feature Name Min Max Inc Valid Values Documentation
EventLine11AnyEdgeData A category that contains all the data features related to the EventLine11AnyEdge event.
EventLine11AnyEdge INT64_MIN INT64_MAX 0x1 - This feature returns the unique identifier of the 'EventLine11AnyEdge' event.
EventLine11AnyEdgeStreamChannelIndex INT64_MIN INT64_MAX 1 - Returns the index of the stream channel that generated the 'EventLine11AnyEdge' event.
EventLine11AnyEdgeFrameID INT64_MIN INT64_MAX 1 - Returns the unique Identifier of the frame (or image) that generated the 'Event Line 11 Any Edge Frame ID' event.
EventLine11AnyEdgeTimestamp INT64_MIN INT64_MAX 1 - Returns the timestamp of the 'Event Line 11 Any Edge Timestamp' event. It can be used to determine when the event occurred.
Feature Name Min Max Inc Valid Values Documentation
EventFrameEndData A category that contains all the data features related to the EventFrameEnd event.
EventFrameEnd INT64_MIN INT64_MAX 0x1 - This feature returns the unique identifier of the 'EventFrameEnd' event.
EventFrameEndStreamChannelIndex INT64_MIN INT64_MAX 1 - Returns the index of the stream channel that generated the 'EventFrameEnd' event.
EventFrameEndFrameID INT64_MIN INT64_MAX 1 - Returns the unique Identifier of the frame (or image) that generated the 'Event Frame End Frame ID' event.
EventFrameEndTimestamp INT64_MIN INT64_MAX 1 - Returns the timestamp of the 'Event Frame End Timestamp' event. It can be used to determine when the event occurred.
Feature Name Min Max Inc Valid Values Documentation
EventDeviceTemperatureStateNormalData A category that contains all the data features related to the EventDeviceTemperatureStateNormal event.
EventDeviceTemperatureStateNormal INT64_MIN INT64_MAX 0x1 - This feature returns the unique identifier of the 'EventDeviceTemperatureStateNormal' event.
EventDeviceTemperatureStateNormalTimestamp INT64_MIN INT64_MAX 1 - Returns the timestamp of the 'Event Device Temperature State Normal Timestamp' event. It can be used to determine when the event occurred.
Feature Name Min Max Inc Valid Values Documentation
EventDeviceTemperatureStateCriticalData A category that contains all the data features related to the EventDeviceTemperatureStateCritical event.
EventDeviceTemperatureStateCritical INT64_MIN INT64_MAX 0x1 - This feature returns the unique identifier of the 'EventDeviceTemperatureStateCritical' event.
EventDeviceTemperatureStateCriticalTimestamp INT64_MIN INT64_MAX 1 - Returns the timestamp of the 'Event Device Temperature State Critical Timestamp' event. It can be used to determine when the event occurred.
Feature Name Min Max Inc Valid Values Documentation
EventDeviceTemperatureStateOverTemperatureData A category that contains all the data features related to the EventDeviceTemperatureStateOverTemperature event.
EventDeviceTemperatureStateOverTemperature INT64_MIN INT64_MAX 0x1 - This feature returns the unique identifier of the 'EventDeviceTemperatureStateOverTemperature' event.
EventDeviceTemperatureStateOverTemperatureTimestamp INT64_MIN INT64_MAX 1 - Returns the timestamp of the 'Event Device Temperature State Over Temperature Timestamp' event. It can be used to determine when the event occurred.
Feature Name Min Max Inc Valid Values Documentation
EventTestData A category that contains all the data features related to the EventTest event.
EventTest INT64_MIN INT64_MAX 0x1 - This feature returns the unique identifier of the 'EventTest' event.
EventTestTimestamp INT64_MIN INT64_MAX 1 - Returns the timestamp of the 'Event Test Timestamp' event. It can be used to determine when the event occurred.